Unable to connect to internet (frugal install; optus cable)
Unable to connect to internet (frugal install; optus cable)
I install successful frugal of the Puppy, but am unable to connect to internet. I have optus cable, I try the wizard, but not work
Thanks for your advice
Thanks for your advice
-
- Posts: 56
- Joined: Wed 09 Dec 2009, 01:20
OK, that's a beggining.
You wrote
Do you see any identified Interfaces? ("eth0", "wlan0").
If you see any interface already detected, you must click at the respective button (let's say "eth0" button), and then choose DHCP in the next dialog.
IF you don't see any identified Interfaces, then your network adapter was not autodetected. You need to get the chipset that the network adapter uses, and then load the module manually.
Can you find that info? Any User Guide, manufacturer, model, can help to find that info.
If you have Windows running on that machine, you can boot windows and look for that info there.
Or, if you can, just open the computer and look at the big chip on the network adapter.
You wrote
That's the message at the bottom of the Network Wizard window.I click the connect >> internet by network
the message is that "it appears the driver module for a network adaptor is not loaaded, or you want a difference one"
. I am stuck there.
Do you see any identified Interfaces? ("eth0", "wlan0").
If you see any interface already detected, you must click at the respective button (let's say "eth0" button), and then choose DHCP in the next dialog.
IF you don't see any identified Interfaces, then your network adapter was not autodetected. You need to get the chipset that the network adapter uses, and then load the module manually.
Can you find that info? Any User Guide, manufacturer, model, can help to find that info.
If you have Windows running on that machine, you can boot windows and look for that info there.
Or, if you can, just open the computer and look at the big chip on the network adapter.
Do you see any identified Interfaces? ("eth0", "wlan0").
Yes I can see eth0 and then I choose DHCP. It is autodeteded. When I opened the IP static I can see the setting, but when I browsed internet it it not connected. I have try to ping few addresses, I can ping yahoo.com, but no response when ping google.com, as well as other addresses
I tried to manually to add default gw, but it is not successful
You advised to turn off firewall, I do not know how to do it in Puppy.
These are the detail of my computer attached as detected Belarc
Operating System System Model
Windows XP Professional (build 2600)
Install Language: English (United States)
System Locale: English (United States) Enclosure Type: Desktop
Processor a Main Circuit Board b
1.60 gigahertz AMD Sempron
128 kilobyte primary memory cache
256 kilobyte secondary memory cache
64-bit ready
Not hyper-threaded Board: Gigabyte Technology Co., Ltd. K8M800-8237
Bus Clock: 200 megahertz
BIOS: Award Software International, Inc. FB 07/21/2005
Drives Memory Modules c,d
240.06 Gigabytes Usable Hard Drive Capacity
130.78 Gigabytes Hard Drive Free Space
TSSTcorp CD/DVDW SH-W162C [CD-ROM drive]
3.5" format removeable media [Floppy drive]
Brother MFC-260C USB Device [Hard drive] -- drive 2
MAXTOR S TM3160215AS SCSI Disk Device (160.04 GB) -- drive 1
ST380011A [Hard drive] (80.03 GB) -- drive 0, s/n 5JV5F16Y, rev 8.01, SMART Status: Healthy 704 Megabytes Usable Installed Memory
Slot 'A0' has 256 MB
Slot 'A1' has 512 MB
Local Drive Volumes
c: (NTFS on drive 0) 41.94 GB 14.55 GB free
d: (NTFS on drive 0) 38.08 GB 33 MB free
f: (NTFS on drive 1) 41.94 GB 38.35 GB free
h: (NTFS on drive 1) 41.94 GB 39.94 GB free
i: (NTFS on drive 1) 76.16 GB 37.91 GB free
Network Drives
None detected
Users (mouse over user name for details) Printers
local user accounts last logon
Guest 4/22/2009 9:47:34 PM
trang 1/1/2010 10:19:56 PM
Tung 1/4/2010 5:25:56 PM (admin)
local system accounts
Administrator never (admin)
HelpAssistant never
SUPPORT_388945a0 never
DISABLED Marks a disabled account; LOCKED OUT Marks a locked account
Brother MFC-260C Printer on USB001
Microsoft Office Document Image Writer Driver on Microsoft Document Imaging Writer Port:
Controllers Display
Standard floppy disk controller
Primary IDE Channel [Controller]
Secondary IDE Channel [Controller]
VIA Bus Master IDE Controller VIA/S3G UniChrome Pro IGP [Display adapter]
BenQ FP91G [Monitor] (19.1"vis, August 2005)
Bus Adapters Multimedia
VIA SATA RAID Controller
VIA Rev 5 or later USB Universal Host Controller (4x) Realtek AC'97 Audio for VIA (R) Audio Controller
Unimodem Half-Duplex Audio Device
Virus Protection [Back to Top] new Group Policies
No details available None discovered
Communications Other Devices
PCI SoftV92 Modem
VIA Rhine II Fast Ethernet Adapter
primary Auto IP Address: 192.168.1.3 / 24
Gateway: 192.168.1.1
Dhcp Server: 192.168.1.1
Physical Address: 00:0F:EA:33:67:51
Networking Dns Server: 192.168.1.1
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
PS/2 Compatible Mouse
USB Composite Device
USB Mass Storage Device
USB Printing Support
USB Root Hub (4x)
Yes I can see eth0 and then I choose DHCP. It is autodeteded. When I opened the IP static I can see the setting, but when I browsed internet it it not connected. I have try to ping few addresses, I can ping yahoo.com, but no response when ping google.com, as well as other addresses
I tried to manually to add default gw, but it is not successful
You advised to turn off firewall, I do not know how to do it in Puppy.
These are the detail of my computer attached as detected Belarc
Operating System System Model
Windows XP Professional (build 2600)
Install Language: English (United States)
System Locale: English (United States) Enclosure Type: Desktop
Processor a Main Circuit Board b
1.60 gigahertz AMD Sempron
128 kilobyte primary memory cache
256 kilobyte secondary memory cache
64-bit ready
Not hyper-threaded Board: Gigabyte Technology Co., Ltd. K8M800-8237
Bus Clock: 200 megahertz
BIOS: Award Software International, Inc. FB 07/21/2005
Drives Memory Modules c,d
240.06 Gigabytes Usable Hard Drive Capacity
130.78 Gigabytes Hard Drive Free Space
TSSTcorp CD/DVDW SH-W162C [CD-ROM drive]
3.5" format removeable media [Floppy drive]
Brother MFC-260C USB Device [Hard drive] -- drive 2
MAXTOR S TM3160215AS SCSI Disk Device (160.04 GB) -- drive 1
ST380011A [Hard drive] (80.03 GB) -- drive 0, s/n 5JV5F16Y, rev 8.01, SMART Status: Healthy 704 Megabytes Usable Installed Memory
Slot 'A0' has 256 MB
Slot 'A1' has 512 MB
Local Drive Volumes
c: (NTFS on drive 0) 41.94 GB 14.55 GB free
d: (NTFS on drive 0) 38.08 GB 33 MB free
f: (NTFS on drive 1) 41.94 GB 38.35 GB free
h: (NTFS on drive 1) 41.94 GB 39.94 GB free
i: (NTFS on drive 1) 76.16 GB 37.91 GB free
Network Drives
None detected
Users (mouse over user name for details) Printers
local user accounts last logon
Guest 4/22/2009 9:47:34 PM
trang 1/1/2010 10:19:56 PM
Tung 1/4/2010 5:25:56 PM (admin)
local system accounts
Administrator never (admin)
HelpAssistant never
SUPPORT_388945a0 never
DISABLED Marks a disabled account; LOCKED OUT Marks a locked account
Brother MFC-260C Printer on USB001
Microsoft Office Document Image Writer Driver on Microsoft Document Imaging Writer Port:
Controllers Display
Standard floppy disk controller
Primary IDE Channel [Controller]
Secondary IDE Channel [Controller]
VIA Bus Master IDE Controller VIA/S3G UniChrome Pro IGP [Display adapter]
BenQ FP91G [Monitor] (19.1"vis, August 2005)
Bus Adapters Multimedia
VIA SATA RAID Controller
VIA Rev 5 or later USB Universal Host Controller (4x) Realtek AC'97 Audio for VIA (R) Audio Controller
Unimodem Half-Duplex Audio Device
Virus Protection [Back to Top] new Group Policies
No details available None discovered
Communications Other Devices
PCI SoftV92 Modem
VIA Rhine II Fast Ethernet Adapter
primary Auto IP Address: 192.168.1.3 / 24
Gateway: 192.168.1.1
Dhcp Server: 192.168.1.1
Physical Address: 00:0F:EA:33:67:51
Networking Dns Server: 192.168.1.1
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
PS/2 Compatible Mouse
USB Composite Device
USB Mass Storage Device
USB Printing Support
USB Root Hub (4x)
OK, it seems that you are already connected and obtained an IP and DSN servers from 192.168.1.1
So it could be a problem related to DNS solving names.
What is inside the /etc/resolv.conf file?
Can you obtain the DNS servers from your ISP and load it manually?
Do you have another OS that works OK to check gateway and DNS servers?
Regarding the firewall, if you never started it, you don't need to turn it off.
So it could be a problem related to DNS solving names.
What is inside the /etc/resolv.conf file?
Can you obtain the DNS servers from your ISP and load it manually?
Do you have another OS that works OK to check gateway and DNS servers?
Regarding the firewall, if you never started it, you don't need to turn it off.
Yes, Window XP works well with the internet
The error message is "Could not set default route through 192.168.1.1. Note that Puppy has tried to do this route add -net default gw 192.168.1.1 and got the following message: route SIOCADDRT: File Exists".
Of interest I can browse anything from www.mozilla.org/projects, but can not get out of this site
I got the DNS servers numbers, manually add on Static IP and the same message appeared as SIOCADDRT file exist.
The error message is "Could not set default route through 192.168.1.1. Note that Puppy has tried to do this route add -net default gw 192.168.1.1 and got the following message: route SIOCADDRT: File Exists".
Of interest I can browse anything from www.mozilla.org/projects, but can not get out of this site
I got the DNS servers numbers, manually add on Static IP and the same message appeared as SIOCADDRT file exist.
I have changes the /etc/resolv.conf file? is : nameserver: to DNS numbers, but still not connected to the internet
I tried to ping one of the DNS numbers the ping is O.K
Ping Localhost is O.K,but still not connected to the internet
I can ping www.google.com is OK, but unable to use internet
The ping is looping and looping
I tried to ping one of the DNS numbers the ping is O.K
Ping Localhost is O.K,but still not connected to the internet
I can ping www.google.com is OK, but unable to use internet
The ping is looping and looping
One last check:
In your windows, open a DOS console, and type
And check the settings that Windows is using, and compare it with the settings Puppy uses.
gposil,
In your windows, open a DOS console, and type
Code: Select all
C:\>ipconfig /all
gposil,
I agree with that, but my resolv.conf file contains only 192.168.1.1, and my modem-router deals with the ISP DNS and resolves everything...The /etc/resolv.conf file should contain you DNS server list from your ISP or whichever DNS servers you use....
a file with the name in bold means that it was modified, but I don't know how you have 2 files with the same name in the same place. There must be a difference between them.
I can see your windows settings in your previous post...
This same settings should be OK for Puppy.
Try puppy as Live CD in this same computer ignoring any saved session (puppy pfix=ram), using DHCP. Then try using an static IP (192.168.1.10 , default gateway 192.168.1.1, DNS server 192.168.1.1 or your ISP DNS servers) and try another puppy version. I really don' t know what is going wrong.
I can see your windows settings in your previous post...
your windows is working OK via DHCP, and the DHCP server is 192.168.1.1VIA Rhine II Fast Ethernet Adapter
primary Auto IP Address: 192.168.1.3 / 24
Gateway: 192.168.1.1
Dhcp Server: 192.168.1.1
Physical Address: 00:0F:EA:33:67:51
Networking Dns Server: 192.168.1.1
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
This same settings should be OK for Puppy.
Try puppy as Live CD in this same computer ignoring any saved session (puppy pfix=ram), using DHCP. Then try using an static IP (192.168.1.10 , default gateway 192.168.1.1, DNS server 192.168.1.1 or your ISP DNS servers) and try another puppy version. I really don' t know what is going wrong.
Hi
I had the same problem after my frugal install (dual boot with WIN XP).
The connection wizard was great with a live CD but following Frugal it would see my wireless LAN device, it would find the network but would not connect. After a number of attempts at restarting the wizard it would simply fail to load.
I used the Pwireless connector (in the network menu) - it found my device, network and connects each time. It doesn't store my profile so have to scan for the network each time.
Have a look at the Network menu to see if there is another application that suits
Linbie (LINex newBIE)
I had the same problem after my frugal install (dual boot with WIN XP).
The connection wizard was great with a live CD but following Frugal it would see my wireless LAN device, it would find the network but would not connect. After a number of attempts at restarting the wizard it would simply fail to load.
I used the Pwireless connector (in the network menu) - it found my device, network and connects each time. It doesn't store my profile so have to scan for the network each time.
Have a look at the Network menu to see if there is another application that suits
Linbie (LINex newBIE)