Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Sat 02 Aug 2014, 02:49
All times are UTC - 4
 Forum index » House Training » Users ( For the regulars )
Hardinfo sensors temp1 -> where get the sensor the temp.
Moderators: Flash, Ian, JohnMurga
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 1 [6 Posts]  
Author Message
HoerMirAuf


Joined: 22 Jan 2008
Posts: 87
Location: Würzburg

PostPosted: Tue 12 Mar 2013, 02:46    Post subject:  Hardinfo sensors temp1 -> where get the sensor the temp.  

Hi Volks....

i use slacko 5.5. Hardinfo shows a temperature sensor temp1. I want to display the temp in conky .... but where can i get this temp? acpitemp dont work and i haven't a thermal_zone in /proc/acpi.

But where get the sensor in hardinfo the shown temperature?

can anybody explain this please?

Thx a lot ! Smile
Back to top
View user's profile Send private message 
Flash
Official Dog Handler


Joined: 04 May 2005
Posts: 10962
Location: Arizona USA

PostPosted: Tue 12 Mar 2013, 08:52    Post subject:  

If you're asking where the temperature sensor is physically located on the board, I think all CPUs are manufactured with a p-n junction diode on the chip that is specifically intended to be used to measure the temperature of the CPU chip itself. However, the motherboard requires circuitry external to the CPU in order to use the diode as a temperature sensor. I think that's how it works. You could probably find out for sure from the website of your CPU's manufacturer. Just download the 5000-page manual for your CPU. Laughing
Back to top
View user's profile Send private message 
rokytnji


Joined: 20 Jan 2009
Posts: 1290
Location: Pecos/ Texas

PostPosted: Tue 12 Mar 2013, 09:55    Post subject:  

Do you have something in /sys/class/hwmon?

Have you installed lmsensors? Have you ran sensors-detect after installing and configuring lmsensors.



http://www.murga-linux.com/puppy/viewtopic.php?t=57480



Quote:
lm_sensors-3.1.2.pet


Get it at

http://www.murga-linux.com/puppy/viewtopic.php?t=74702

then read up on running sensors-detect.
Back to top
View user's profile Send private message Visit poster's website 
rjbrewer


Joined: 22 Jan 2008
Posts: 4422
Location: merriam, kansas

PostPosted: Tue 12 Mar 2013, 12:26    Post subject:  

Cputemp will give you a tray icon that can be clicked to
show temp.

http://murga-linux.com/puppy/viewtopic.php?p=432546&search_id=1575727046#432546

_________________

Inspiron 700m, Pent.M 1.6Ghz, 1Gb ram.
Msi Wind U100, N270 1.6>2.0Ghz, 1.5Gb ram.
Eeepc 8g 701, 900Mhz, 1Gb ram.
Full installs

Back to top
View user's profile Send private message 
Karl Godt


Joined: 20 Jun 2010
Posts: 3956
Location: Kiel,Germany

PostPosted: Tue 12 Mar 2013, 12:41    Post subject:  

bash-3.00#
Code:
 find /sys -name "temp*"

/sys/devices/platform/coretemp.0/temp3_input
/sys/devices/platform/coretemp.0/temp3_label
/sys/devices/platform/coretemp.0/temp2_crit_alarm
/sys/devices/platform/coretemp.0/temp2_crit
/sys/devices/platform/coretemp.0/temp3_crit
/sys/devices/platform/coretemp.0/temp3_crit_alarm
/sys/devices/platform/coretemp.0/temp2_max
/sys/devices/platform/coretemp.0/temp3_max
/sys/devices/platform/coretemp.0/temp2_input
/sys/devices/platform/coretemp.0/temp2_label

_________________
«Give me GUI or Death» -- I give you [[Xx]term[inal]] [[Cc]on[s][ole]] .
Macpup user since 2010 on full installations.
People who want problems with Puppy boot frugal Razz
Back to top
View user's profile Send private message Visit poster's website 
HoerMirAuf


Joined: 22 Jan 2008
Posts: 87
Location: Würzburg

PostPosted: Wed 13 Mar 2013, 04:22    Post subject:  

Hi folks ....

thanks so much for your replies an your hints!!:

@Flash ....
thank you for your hint. But i was searching for the file where the temp-data is stored. Sorry, my english isn't very good, i think i haven't good enunciated me.

@rokytnji
thank you too for this hint. It give me some approach. In /sys/class/hwmon is a subfolder hwmon0 with som files in it. But is there the temp-info stored? lm_sensor 3.1.2 can't find any temp sensor. But i searched around an found to modprobe coretemp. After modprobe coretemp there are 4 temperature-sensors in hwmon and in terminal after using command "sensors":
Code:

nouveau-pci-0100
Adapter: PCI adapter
temp1:       +42.0 C  (high = +100.0 C, crit = +110.0 C) 

coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +49.0 C  (high = +87.0 C, crit = +105.0 C) 
Core 0:        +49.0 C  (high = +87.0 C, crit = +105.0 C) 
Core 1:        +41.0 C  (high = +87.0 C, crit = +105.0 C) 

nouveau seems to be the graphiccard temperature
core 0 and core 1 should be the temperature form the both cpu-cores.
What the Physical id0 temp is, i don't know....

After searching further for lm_sensor hwmon and conky... i found out that i can use the hwon temperature direct in conky with:

${hwmon 0 temp 1} for the nouveau temperature
${hwmon 1 temp 2} for the 1st core temperature
${hwmon 1 temp 3} for the 2nd core temperature

@rjbrewer
thank your for your hint ..... you are right, but i want to use conky and dont want further traybuttons Smile

@Karl Godt
cool! That was just what i was looking for. Well i have just found another solution, but your way is good to know!


Thank you all a lot for your help!!!
Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 1 of 1 [6 Posts]  
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » House Training » Users ( For the regulars )
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0577s ][ Queries: 11 (0.0038s) ][ GZIP on ]