Page 1 of 1
SoftMaker 2008 installation (SOLVED)
Posted: Sun 04 Dec 2011, 18:41
by rincon155
I have SoftMaker 2008, but every time I open it there is a menu for the initial installation asking to set the location for documents in /root/SoftMaker.
After accepting the menu everything is fine.
How can I avoid that menu for initial installation every-time I open the program?
Posted: Mon 05 Dec 2011, 20:16
by SFR
I suppose that you have
THIS (12,1M) built installed, because I have encountered exactly the same issue (with Presentations module only!).
After small investigation I think I found the solution:
Go to
/usr/share/office2008/designs/
and rename
44_simple.prv to
01_glass.prv
Launch Presentations, accept path, exit and launch it again.
This solution seems to be a bit mysterious (even for me
), but I guess that Presentations' binary is looking for this specific one every time it's starting. And this built is sorely stripped down...
Hope this helps.
Greetings!
Posted: Tue 06 Dec 2011, 01:58
by rincon155
SFR wrote:I suppose that you have
THIS (12,1M) built installed, because I have encountered exactly the same issue (with Presentations module only!).
After small investigation I think I found the solution:
Go to
/usr/share/office2008/designs/
and rename
44_simple.prv to
01_glass.prv
Launch Presentations, accept path, exit and launch it again.
This solution seems to be a bit mysterious (even for me
), but I guess that Presentations' binary is looking for this specific one every time it's starting. And this built is sorely stripped down...
Hope this helps.
Greetings!
I did it, It works perfect for the Presentation module!!!
The word processor and spreadsheet are not affected. The bug stay the same for them. Can you figure out a similar fix for those?
Posted: Tue 06 Dec 2011, 08:19
by SFR
Can you point me to version of SoftMaker2008 you are using?
I'll download it and see what I can do.
Greetings!
Posted: Tue 06 Dec 2011, 10:22
by SFR
Meanwhile maybe this will help you.
Check out if you have these files:
/usr/share/office2008/install_en/Templates/English/Normal.tmv
/usr/share/office2008/install_en/Templates/English/PlanMaker/Normal.pmv
If they don't exist, just create blank document template (Textmaker), save it as Normal.tmv and blank spreadsheet template (Planmaker), save it as Normal.pmv, and put them there.
Greetings!
Posted: Wed 07 Dec 2011, 00:37
by rincon155
SFR wrote:Can you point me to version of SoftMaker2008 you are using?
I'll download it and see what I can do.
Greetings!
TextMaker for Linux (rev 503)
PlanMaker for Linux (rev 503)
Posted: Wed 07 Dec 2011, 00:43
by rincon155
SFR wrote:Meanwhile maybe this will help you.
Check out if you have these files:
/usr/share/office2008/install_en/Templates/English/Normal.tmv
/usr/share/office2008/install_en/Templates/English/PlanMaker/Normal.pmv
If they don't exist, just create blank document template (Textmaker), save it as Normal.tmv and blank spreadsheet template (Planmaker), save it as Normal.pmv, and put them there.
Greetings!
Yes, I have both
Posted: Wed 07 Dec 2011, 15:27
by SFR
rincon155 wrote:SFR wrote:Can you point me to version of SoftMaker2008 you are using?
I'll download it and see what I can do.
Greetings!
TextMaker for Linux (rev 503)
PlanMaker for Linux (rev 503)
My mistake
. I mean can you point me to
place you downloaded SoftMaker from?
It's hard to say anything, because I'm still not sure we have the same built.
Another blind shot:
rincon155 wrote:every time I open it there is a menu for the initial installation asking to set the location for documents in /root/SoftMaker.
It's true regarding Presentations, but when I launch TextMaker or PlanMaker for the first time, there are TWO paths displayed (for Document folder & Template folder). And sometimes one of them contains
?/ string instead of
/root/SoftMaker/Templates/
This causes reappearing of initial dialog in my case.
Check if you also have this string displayed and provide correct path (and don't forget to add slash
/ at the end of path).
Greetings!
Posted: Wed 07 Dec 2011, 22:15
by rincon155
SFR wrote:rincon155 wrote:SFR wrote:Can you point me to version of SoftMaker2008 you are using?
I'll download it and see what I can do.
Greetings!
TextMaker for Linux (rev 503)
PlanMaker for Linux (rev 503)
My mistake
. I mean can you point me to
place you downloaded SoftMaker from?
It's hard to say anything, because I'm still not sure we have the same built.
Another blind shot:
rincon155 wrote:every time I open it there is a menu for the initial installation asking to set the location for documents in /root/SoftMaker.
It's true regarding Presentations, but when I launch TextMaker or PlanMaker for the first time, there are TWO paths displayed (for Document folder & Template folder). And sometimes one of them contains
?/ string instead of
/root/SoftMaker/Templates/
This causes reappearing of initial dialog in my case.
Check if you also have this string displayed and provide correct path (and don't forget to add slash
/ at the end of path).
Greetings!
I downloaded SoftMaker 2008 from Barry's Blog:
http://bkhome.org/blog/?viewDetailed=02435
Yes, I always get the ?/ sting.
Tonight, when I will access my home computer I will see the specific path and will post it.
Thank you for all your dedication to solve this bug.
Posted: Wed 07 Dec 2011, 23:06
by SFR
Ok, I have this one too.
rincon155 wrote:Yes, I always get the ?/ sting.
Good, just type
/root/SoftMaker/Templates/ there and hopefully everything should be all right now.
Greetings!
Posted: Thu 08 Dec 2011, 00:43
by rincon155
SFR wrote:
Ok, I have this one too.
rincon155 wrote:Yes, I always get the ?/ sting.
Good, just type
/root/SoftMaker/Templates/ there and hopefully everything should be all right now.
Greetings!
Again, I applied your suggestion and the bug disappeared!!!
After initial windows in TextMaker and in the PlanMaker, the second time both opened normally.
Thank you very much!!!!