lucid pup 520 creates a swap file?

Using applications, configuring, problems
Post Reply
Message
Author
User avatar
enhu
Posts: 302
Joined: Wed 27 May 2009, 02:13
Contact:

lucid pup 520 creates a swap file?

#1 Post by enhu »

i saw this during boot up and lok for the file and its named pupswap.swp

why didn't it use the swap partition i've made using the gparted?

nooby
Posts: 10369
Joined: Sun 29 Jun 2008, 19:05
Location: SwedenEurope

#2 Post by nooby »

others have referred to it too. Where does it get created on your HDD?

Did you do full install or a frugal isntall or using CD or USB or what

I try to find it on my acer too.

Pfind says that I have no such file on my HDD. So where can I look for it?
pupswap.swp

I did a frugal install of both luci252 and of Snowpup 013 yesterday and if it is like you say I would ahve two such files because both OS are Lupu 5.2 based

Eidt, Now I have manually looked through three partitions andthere are no pupswap file nowhere to be found.

Have you made a full install then?
I use Google Search on Puppy Forum
not an ideal solution though

User avatar
enhu
Posts: 302
Joined: Wed 27 May 2009, 02:13
Contact:

#3 Post by enhu »

its in /mnt/home

frugal install and the lucid just stays in the boot directory.

i have slack installed in the 1st partition and lucid in the 2nd.

i've attached a shot.
Attachments
swap.png
(20.61 KiB) Downloaded 949 times

nooby
Posts: 10369
Joined: Sun 29 Jun 2008, 19:05
Location: SwedenEurope

#4 Post by nooby »

Thanks Enhu, we have to wait then for explanation from those who knows what the internal scripts are doing at that time it creates that file there.

another user complained about why it did not make use of the swap file he already got. Maybe they have answered him there in that thread. I try to find it and refer to it here too?

More difficult to find using google than I thought. I do a manual search of two threads and then I give up on it. okay? :)

Ha ha it could be this thread and starting here

http://www.murga-linux.com/puppy/viewto ... 698#483873

As I get it. If the RAM memory is less than 256MB and regardless if there already exists a swap file or swap partition the woof? script does create such a file in case it is needed.

Could that be as I get that text?

Check it out that could explain why you have it and me not. I have 1GB of memory so the script did not create one. Do you have 256 or less?
I use Google Search on Puppy Forum
not an ideal solution though

Sylvander
Posts: 4416
Joined: Mon 15 Dec 2008, 11:06
Location: West Lothian, Scotland, UK

#5 Post by Sylvander »

1. Perhaps the swap FILE had already been made by the time you got around to making the swap PARTITION.

2. Use some OS that doesn't make use of either the swap partition or file, to delete the swap file.
e.g. I used the "Seagate Disk Wizard" to delete my Linux swap partition.
What I use to delete a swap file would depend...
Windows could do it if is capable of reading/writing the partition_file_system.

User avatar
enhu
Posts: 302
Joined: Wed 27 May 2009, 02:13
Contact:

#6 Post by enhu »

could it be because i only have 256 of RAM?

from dmseg command:

Code: Select all

NET: Registered protocol family 23
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
via-rhine: Broken BIOS detected, avoid_D3 enabled.
ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
via-rhine 0000:00:12.0: PCI INT A -> Link[ALKD] -> GSI 23 (level, low) -> IRQ 23
eth0: VIA Rhine II at 0x1e800, 00:11:5b:03:bc:c0, IRQ 23.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 45e1.
Adding 204792k swap on /initrd/mnt/dev_save/pupswap.swp.  Priority:-1 extents:55 across:806312k 
input: PC Speaker as /devices/platform/pcspkr/input/input5
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ip_tables: (C) 2000-2006 Netfilter Core Team
in there is - Adding 204792k swap on /initrd/mnt/dev_save/pupswap.swp. Priority:-1 extents:55 across:806312k

User avatar
Makoto
Posts: 1665
Joined: Fri 04 Sep 2009, 01:30
Location: Out wandering... maybe.

#7 Post by Makoto »

Are you sure it's not actually using both the swap file and swap partition? Based upon what I've read, Puppy will happily use all of the swap files/partitions it finds, even more than one at a time.

Open a terminal/console and use the "free" command to see how much swap memory is being used. If you know both the sizes of your swap partition and the pupswap.swp file, it may indicate both are being used.

Could the pupswap.swp be a remnant of an earlier Puppy setup? I've heard some setups do automatically create a pupswap.swp file, regardless...
[ Puppy 4.3.1 JP, Frugal install ] * [ XenialPup 7.5, Frugal install ] * [XenialPup 64 7.5, Frugal install] * [ 4GB RAM | 512MB swap ]
In memory of our beloved American Eskimo puppy (1995-2010) and black Lab puppy (1997-2011).

User avatar
enhu
Posts: 302
Joined: Wed 27 May 2009, 02:13
Contact:

#8 Post by enhu »

the attached file is the result using the free command.

so what i did is reformat my swap partition so now pup uses 1gb of swap.
yet still the pupswap.swp file in /mnt/home is still there after rebooting. :D

during its booting, i can see that sda3 [ the swap partition] is now used.
Attachments
free.png
(5.2 KiB) Downloaded 388 times

Post Reply