Drivers for Puppy 5.1-5.2.8 with 2.6.33.2 kernel
New Broadcom STA wl pet for lupu k2.6.33
I've created a new version of the Broadcom-STA pet for lupu-528
The latest version is attached to rerwin's post:
http://murga-linux.com/puppy/viewtopic. ... start=1486
This pet is an update of the one previously made by piratesmack using the latest Broadcom sources and new installation and startup logic developed by rerwin.
The background (and equivalent pets for other puppies) are described:
http://www.murga-linux.com/puppy/viewto ... 360#609360
If anybody tests it please provide feedback - thanks.
Cheers
peebee
The latest version is attached to rerwin's post:
http://murga-linux.com/puppy/viewtopic. ... start=1486
This pet is an update of the one previously made by piratesmack using the latest Broadcom sources and new installation and startup logic developed by rerwin.
The background (and equivalent pets for other puppies) are described:
http://www.murga-linux.com/puppy/viewto ... 360#609360
If anybody tests it please provide feedback - thanks.
Cheers
peebee
Last edited by peebee on Thu 26 Apr 2012, 06:29, edited 2 times in total.
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
-
- Posts: 5464
- Joined: Fri 10 Jun 2005, 05:12
- Location: Australia
All you need to do is run the "make" command ...Semme wrote:Hi Tempestuous, would you afford me a quick overview on how you built this pkg- so I can learn something for my effort?
but I think you first need fully configured kernel sources!
By this, I mean that not only does the kernel source need to be present, it also needs to be configured, and maybe also compiled. This will ensure that all the necessary kernel source headers are built.
To configure your kernel source, do this -
Code: Select all
cd /usr/src/linux-2.6.33.2
make menuconfig
This simple exercise will create a number of kernel configuration files. At this point it's feasible that you can go ahead and compile your "easy-slow-down-manager" package, but maybe not ... so proceed to the full kernel compilation -
Code: Select all
make bzImage
Code: Select all
make modules
-
- Posts: 5464
- Joined: Fri 10 Jun 2005, 05:12
- Location: Australia
Here are several ADSL USB modem drivers, of the modem-type which uses "PPP over ATM" communication.
The following 5 drivers are included:
cxacru - for the Conexant AccessRunner
speedtch - for the Alcatel SpeedTouch
ueagle-atm - for the ADI 930/Eagle
usbatm - for generic USB ATM/DSL modems
xusbatm - for USB ADSL modems initialized in userspace
I have included the necessary firmware for the ueagle-atm driver, but I cannot legally provide the necessary firmware for the cxacru and speedtch drivers. You will need to find this firmware, yourself, and place it in /lib/firmware
The cxacru driver requires: cxacru-fw.bin
The speedtch driver requires: speedtch-1.bin and speedtch-2.bin
And since PPP-over-ATM is not supported in Puppy Lucid (nor any other standard Puppy), you must also install the ATM networking drivers.
Here are the 2 dotpets -
http://www.smokey01.com/tempestuous/atm-k2.6.33.2.pet
http://www.smokey01.com/tempestuous/USB ... 6.33.2.pet
After installing these dotpets, reboot.
Configuration is explained by forum member jaydee here -
http://www.murga-linux.com/puppy/viewto ... 473#621473
The following 5 drivers are included:
cxacru - for the Conexant AccessRunner
speedtch - for the Alcatel SpeedTouch
ueagle-atm - for the ADI 930/Eagle
usbatm - for generic USB ATM/DSL modems
xusbatm - for USB ADSL modems initialized in userspace
I have included the necessary firmware for the ueagle-atm driver, but I cannot legally provide the necessary firmware for the cxacru and speedtch drivers. You will need to find this firmware, yourself, and place it in /lib/firmware
The cxacru driver requires: cxacru-fw.bin
The speedtch driver requires: speedtch-1.bin and speedtch-2.bin
And since PPP-over-ATM is not supported in Puppy Lucid (nor any other standard Puppy), you must also install the ATM networking drivers.
Here are the 2 dotpets -
http://www.smokey01.com/tempestuous/atm-k2.6.33.2.pet
http://www.smokey01.com/tempestuous/USB ... 6.33.2.pet
After installing these dotpets, reboot.
Configuration is explained by forum member jaydee here -
http://www.murga-linux.com/puppy/viewto ... 473#621473
Last edited by tempestuous on Wed 27 Aug 2014, 01:41, edited 1 time in total.
2012 Driver B43 is fool and Luci 5.1.1 does not shut down
2012 Driver B43 is fool and Luci 5.1.1 does not shut down
rfkill-upgrade-k2.6.33.2 pet without any result
Have you issued a more recent version of lucid 5.1.1 repaired ?
Good evening.I amFrench, but i understand english, computing not to much.
rfkill-upgrade-k2.6.33.2 pet without any result
Have you issued a more recent version of lucid 5.1.1 repaired ?
Good evening.I amFrench, but i understand english, computing not to much.
-
- Posts: 5464
- Joined: Fri 10 Jun 2005, 05:12
- Location: Australia
I'm guessing by "fool" you mean "not functioning". When you search this forum for "b43" you will see that this driver fails to work with certain (troublesome) models of Broadcom wifi devices. The problem is generally solved in newer Puppy versions with newer kernels and the new "brcmsmac" driver, but with older kernels (such as Lucid has) the only solution is to use the proprietary Broadcom wifi driver - this driver is posted by forum member peebee at the top of this page.Pelo wrote:2012 Driver B43 is fool and Luci 5.1.1 does not shut down
Be careful what you ask for, and what you might presume your solution to be;
No, this should not achieve any different result ... except for what was intended - wifi on/off switching.Pelo wrote:rfkill-upgrade-k2.6.33.2 pet without any result
I have never issued any version of Lucid "repaired".Pelo wrote:Have you issued a more recent version of lucid 5.1.1 repaired ?
Does anyone have an explanation for this? I was successfully able to get wireless with a USB dongle, but I'm not sure why it works this way. I'm trying to learn more about Puppy LInux.
My setup is 5.2.8 with update 001 frugal install. For my wireless, I'm using a USB wireless N adapter with a Ralink Chipset, product ID 3070. My router is a linksys wrt120n with WPA2 encryption. The command cat /proc/bus/usb/devices gives me:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=148f ProdID=3070 Rev= 1.01
S: Manufacturer=Ralink
S: Product=802.11 n WLAN
S: SerialNumber=1.0
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I:* If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2870
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
If I use the internet setup wizard, Network Wizard or Simple network setup, the ralink module rt2800usb is loaded. Apparently, this may not work with WPA encryption. Nonetheless, I was unable to establish an internet connection. I installed Frisbee and tried to establish a connection, but again, no luck as expected. The strange thing is that I used a different wireless usb dongle (wireless G with chipset realtek (rtl8187)) to configure my network, establish connection, then replaced the realtek dongle with my ralink dongle, Frisbee connects to the internet consistently (on every boot). Can someone explain this to me?
Also, if I were to start from scratch and not configure the wireless with the realtek usb dongle, install a dot pet with the appropriate driver, do I need to blacklist rt2800usb module?
My setup is 5.2.8 with update 001 frugal install. For my wireless, I'm using a USB wireless N adapter with a Ralink Chipset, product ID 3070. My router is a linksys wrt120n with WPA2 encryption. The command cat /proc/bus/usb/devices gives me:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=148f ProdID=3070 Rev= 1.01
S: Manufacturer=Ralink
S: Product=802.11 n WLAN
S: SerialNumber=1.0
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I:* If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2870
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
If I use the internet setup wizard, Network Wizard or Simple network setup, the ralink module rt2800usb is loaded. Apparently, this may not work with WPA encryption. Nonetheless, I was unable to establish an internet connection. I installed Frisbee and tried to establish a connection, but again, no luck as expected. The strange thing is that I used a different wireless usb dongle (wireless G with chipset realtek (rtl8187)) to configure my network, establish connection, then replaced the realtek dongle with my ralink dongle, Frisbee connects to the internet consistently (on every boot). Can someone explain this to me?
Also, if I were to start from scratch and not configure the wireless with the realtek usb dongle, install a dot pet with the appropriate driver, do I need to blacklist rt2800usb module?
- goolwa_pup
- Posts: 59
- Joined: Thu 29 Oct 2009, 20:31
puppy 528 with momo logitech wheel not working
installed the logitech and joystick utils pets from this thread and after reboot fftest states that force feedback function not implemented..any tricks to make force feedback work in puppy 528?....steering wheel works but no force feedback function
rtl8192cu testing
I downloaded and install the 8192cu.pet. The boot screen indicates that the module in loaded on boot up.
When I run the network setup it does not see the device. Though I can load the module.
I have included snapshots of lsmod and pmodemdiag info.
the lsmod shows it
8192cu 29370 0
Hopefully you can fill in the gaps of info and provide direction.
I am using Puppylinux 5.25 lupu 5.25.
When I run the network setup it does not see the device. Though I can load the module.
I have included snapshots of lsmod and pmodemdiag info.
the lsmod shows it
8192cu 29370 0
Hopefully you can fill in the gaps of info and provide direction.
I am using Puppylinux 5.25 lupu 5.25.
- Spaccafumo
- Posts: 33
- Joined: Thu 15 Jan 2009, 11:06
- Location: Sulmona - Italy
Drivers for Slacko. Kernel 2.6.37.6
Any rt3070sta-2.6.37.6.pet?
-------------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=148f ProdID=3070 Rev= 1.01
S: Manufacturer=Ralink
S: Product=802.11 n WLAN
S: SerialNumber=1.0
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I:* If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2870
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Saluti.
-------------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=148f ProdID=3070 Rev= 1.01
S: Manufacturer=Ralink
S: Product=802.11 n WLAN
S: SerialNumber=1.0
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I:* If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2870
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Saluti.
Qui si usa Linux
http://www.puppylinux.org
Sulmona - Italy
http://www.puppylinux.org
Sulmona - Italy
Please redo an ISO for Lucid 528
people are still realising disabled LUCIDs
LXDE lucid nite flux from spane : no sound, no wifi.
Even now ! we have all the correct drivers available. Please issue a new ISO including them.
And long life to Lucid !
LXDE lucid nite flux from spane : no sound, no wifi.
Even now ! we have all the correct drivers available. Please issue a new ISO including them.
And long life to Lucid !
Pelo and Spaccafumo, I am not a moderator, but I hope you don't mind me telling you that this thread is specifically for: Drivers for Puppy 5.1-5.2.8 with 2.6.33.2 kernel
Please make other requests and comments in the thread where they belong:
Pelo: http://www.murga-linux.com/puppy/viewtopic.php?t=70855
Spaccafumo: http://puppylinux.org/wikka/Puppy53?redirect=no
tallboy
Please make other requests and comments in the thread where they belong:
Pelo: http://www.murga-linux.com/puppy/viewtopic.php?t=70855
Spaccafumo: http://puppylinux.org/wikka/Puppy53?redirect=no
tallboy
True freedom is a live Puppy on a multisession CD/DVD.
I am stuck to my chair because of my laptop wireless
iwlagn :tallboy wrote:Pelo and Spaccafumo, I am not a moderator, but I hope you don't mind me telling you that this thread is specifically for: Drivers for Puppy 5.1-5.2.8 with 2.6.33.2 kernel
tallboy
What does that mean (here after) ?
The only solution at the moment seems to be deactivating wireless N mode and use wireless G mode only.
A lot of work has to be done here.
It will be my last try to be wirelessed with Lucid. I will stay chained to my ethernet cable ! but be cool, i just try to make things working, it's not a disaster ! Any news about this subject ? Merci les gars.
- Attachments
-
- iwlagn.png
- Kernel 2.6.33.2 Lucid 528 with fluxbox
- (11.97 KiB) Downloaded 1885 times
Hi there,
I have an issue with wireless support for my PC. It has Lupu 5.20 installed on it. The RTL8191SE wireless wasn't seen by Puppy at all, so I installed the PET from page two of this thread r8192se_pci-k2.6.33.2.pet It is now seen by the OS, but it won't "wake up". It just gives me an error when I try to connect to the internet with it.
I tried also using Carolina and Precise 5.71 neither of these puppies had any success with the wifi on my PC. These two more modern puppies just tell me wlan is down.
I have a temp fix of using a usb wifi which works (slowly), but it'd be nicer to use the onboard wifi.
Any help?
I have an issue with wireless support for my PC. It has Lupu 5.20 installed on it. The RTL8191SE wireless wasn't seen by Puppy at all, so I installed the PET from page two of this thread r8192se_pci-k2.6.33.2.pet It is now seen by the OS, but it won't "wake up". It just gives me an error when I try to connect to the internet with it.
I tried also using Carolina and Precise 5.71 neither of these puppies had any success with the wifi on my PC. These two more modern puppies just tell me wlan is down.
I have a temp fix of using a usb wifi which works (slowly), but it'd be nicer to use the onboard wifi.
Any help?
-
- Posts: 5464
- Joined: Fri 10 Jun 2005, 05:12
- Location: Australia
What's your computer? A laptop? There might be a wifi on/off switch involved, and it might be an "rfkill" issue.
To complicate matters, the standard release of Puppy 5.2.x (Lupu) did not enable the rfkill driver, so please first install my "rfkill-upgrade" dotpet from earlier in this thread -
http://www.murga-linux.com/puppy/viewto ... 093#452093
Then reboot, and run this command -
Please report the result.
To complicate matters, the standard release of Puppy 5.2.x (Lupu) did not enable the rfkill driver, so please first install my "rfkill-upgrade" dotpet from earlier in this thread -
http://www.murga-linux.com/puppy/viewto ... 093#452093
Then reboot, and run this command -
Code: Select all
rfkill list
My PC is one like this.
http://au.shuttle.com/products/products ... uctId=1675
Not this model though, will have to figure that out when I get home. No switch is involved.
Will try the RFKILL update and see what happens.
Questioning the effectiveness however, as it also didn't work in later puppies. But will try tonight and report back. Thanks
http://au.shuttle.com/products/products ... uctId=1675
Not this model though, will have to figure that out when I get home. No switch is involved.
Will try the RFKILL update and see what happens.
Questioning the effectiveness however, as it also didn't work in later puppies. But will try tonight and report back. Thanks
Precise 5.7.1 (pae version) does have an rfkill problem - seetempestuous wrote:and it might be an "rfkill" issue.
http://www.murga-linux.com/puppy/viewto ... &start=126
LxPup = Puppy + LXDE
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64
Main version used daily: LxPupSc; Assembler of UPups, ScPup & ScPup64, LxPup, LxPupSc & LxPupSc64