Puppy Linux Discussion Forum

[treeplanter]

anyone have luck getting psip going using diamondcard ..I dont see a line to enter the pin for diamond card in the config file.And I'm not sure that psip is working with the sound card ...Micron transport zx....128mb mem. I've got Twinkle installed and it works ...but the echo is driving my friends crazy.I can't hear it on my end, but on the other end of a land line call is apparently very bad....... any other VOIP suggestions??

[gazb]

If you get echo then your microphone is set too loud, you need to make it as quiet as possible then bring it up until you can hear OK without echo.

[watchdog]

Excuse me my bad english. Just yesterday I get working psip32 with Ekiga Call out or Diamond Card in wary 5.3 and slacko 5.3.3. I post my /root/.psip.conf:

{
"account": {
"sip-url": "sip:ID@sip.diamondcard.us",
"registrar": "sip:sip.diamondcard.us",
"realm": "*",
"user": "ID",
"password": "PIN",
"use-srtp": 0,
"proxy": "sip:sip.diamondcard.us"
},
"settings": {
"ring-command": "",
"loglevel": 1,
"help-command": "",
"call-timeout": "15",
"minimise-tray": 0,
"auto-register": 0,
"ringtone-file": "/usr/share/audio/beep_high.wav",
"im-beep": 0,
"im-command": "",
"activity-log": 1,
"sampling-rate": -1,
"max-calls": "2",
"sip-port": "5060",
"public-ip": "",
"stun-server": "",
"disable-vad": 0,
"enable-ice": 0,
"turn-server": "",
"turn-user": "",
"turn-password": "",
"turn-realm": "",
"turn-use-tcp": 0,
"disable-tcp": 1,
"disable-optional-srtp": 0,
"audio-in": "default",
"audio-out": "default"
},
"buddy-categories": []
}

Substitute ID and PIN with the real your ID and PIN of your account with Diamond Card. With some routers you have to substitute the line:

"proxy": "sip:sip.diamondcard.us"

with

"proxy": ""

Dial and add buddies in the way:

sip:0039nationalnumber@sip.diamondcard.us

Substitute 0039 with your desired international prefix (0039 for Italy...).

Best Regards

[watchdog]

For NAT-traversal I experimented another way to do the job with dummy connections. New /root/.psip.conf:

{
"account": {
"sip-url": "sip:ID@sip.diamondcard.us",
"registrar": "sip:sip.diamondcard.us",
"realm": "*",
"user": "ID",
"password": "PIN",
"use-srtp": 0,
"proxy": "sip:sip.diamondcard.us"
},
"settings": {
"ring-command": "",
"loglevel": 1,
"help-command": "",
"call-timeout": "15",
"minimise-tray": 0,
"auto-register": 0,
"ringtone-file": "/usr/share/audio/beep_high.wav",
"im-beep": 0,
"im-command": "",
"activity-log": 1,
"sampling-rate": -1,
"max-calls": "2",
"sip-port": "5060",
"public-ip": "IP",
"stun-server": "stunserver.org",
"disable-vad": 0,
"enable-ice": 0,
"turn-server": "",
"turn-user": "",
"turn-password": "",
"turn-realm": "",
"turn-use-tcp": 0,
"disable-tcp": 1,
"disable-optional-srtp": 0,
"audio-in": "default",
"audio-out": "default"
},
"buddy-categories": []
}

Replace ID and PIN with ID and PIN of your account at Diamondcard. IP is the external IP of the NAT gateway: you can read it by clicking over the monitor of connection low-ritght of the desktop. Enjoy.

[Sylvander]

1.