Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Wed 30 Jul 2014, 19:43
All times are UTC - 4
 Forum index » House Training » HOWTO ( Solutions )
HOWTO pppoe with Puppy (Roaring Penguin)
Moderators: Flash, Ian, JohnMurga
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 1 [1 Post]  
Author Message
Tervel

Joined: 03 Aug 2008
Posts: 1

PostPosted: Sun 03 Aug 2008, 19:14    Post subject:  HOWTO pppoe with Puppy (Roaring Penguin)
Subject description: TESTED on TigerPup 1.6, MacPup and TinyMe
 

HOWTO pppoe with Puppy (Roaring Penguin)
=========================================

TESTED on TigerPup 1.6, MacPup and TinyMe;


I recommend to use the terminal over the RoadPenguin-GUI.

1. Start the Puppy "Network wizard" and configure your LAN-Card (eth0 or eth1)
2.Then click on "auto dhcp" in the "Network wizard"

Now your network is configured.

3. Type in the terminal

"pppoe-setup"

4.You'll be greeted by:

> Welcome to the Roaring Penguin PPPoE client setup. First, I will run
> some checks on your system to make sure the PPPoE client is installed
> properly...
>
> Looks good! Now, please enter some information:

5.Type your account name

> USER NAME
>
> >>> Enter your PPPoE user name (default bxxxnxnx@sympatico.ca): YOURACCOUNT

6.Choose the ETH you activated in the "Network wizard"

> INTERFACE
>
> >>> Enter the Ethernet interface connected to the DSL modem
> For Solaris, this is likely to be something like /dev/hme0.
> For Linux, it will be ethn, where 'n' is a number.
> (default eth1): eth0
>
> Do you want the link to come up on demand, or stay up continuously?
> If you want it to come up on demand, enter the idle time in seconds
> after which the link should be dropped. If you want the link to
> stay up permanently, enter 'no' (two letters, lower-case.)
> NOTE: Demand-activated links do not interact well with dynamic IP
> addresses. You may have some problems with demand-activated links.

7. I chose "NO".

> >>> Enter the demand value (default no): no
>

8. !!!IMPORTANT!!! You HAVE to write in your DNS! The other option didn't work for me.

> Please enter the IP address of your ISP's primary DNS server.

sh-3.00# >>> Enter the DNS information here:(PUT YOUR DNS HERE!)
sh: syntax error near unexpected token `>'
sh-3.00# Please enter the IP address of your ISP's secondary DNS server.
> If you just press enter, I will assume there is only one DNS server.
> >>> Enter the secondary DNS server address here:(PUT YOUR DNS HERE!)

9.Type in your account password.

> PASSWORD
>
> >>> Please enter your PPPoE password:
> >>> Please re-enter your PPPoE password:
>

10. IMPORTANT - I choose always option "1" !!!

> FIREWALLING
>
> Please choose the firewall rules to use. Note that these rules are
> very basic. You are strongly encouraged to use a more sophisticated
> firewall setup; however, these will provide basic security. If you
> are running any servers on your machine, you must choose 'NONE' and
> set up firewalling yourself. Otherwise, the firewall rules will deny
> access to all standard servers like Web, e-mail, ftp, etc. If you
> are using SSH, the rules will block outgoing SSH connections which
> allocate a privileged source port.
>
> The firewall choices are:
> 0 - NONE: This script will not set any firewall rules. You are responsible
> for ensuring the security of your machine. You are STRONGLY
> recommended to use some kind of firewall rules.
> 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
> 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
> for a LAN
> >>> Choose a type of firewall (0-2): 1
>
> ** Summary of what you entered **
>
> Ethernet Interface: eth0
> User name: xxxxxxxx
> Activate-on-demand: No
> Primary DNS: xxx.xx.x.x
> Secondary DNS: xxx.xx.x.x
> Firewalling: STANDALONE

>
> >>> Accept these settings and adjust configuration files (y/n)? y
> Adjusting /etc/ppp/pppoe.conf
> Adjusting /etc/resolv.conf
> Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
> (But first backing it up to /etc/ppp/pap-secrets-bak)
> (But first backing it up to /etc/ppp/chap-secrets-bak)
>
>
>
> Congratulations, it should be all set up!
>
> Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring
> it down. Type 'pppoe-status' to see the link status.

10. Now type "pppoe-start"

> sh-3.00# pppoe-start
> ... Connected!


> sh-3.00# pppoe-status
> pppoe-status: Link is up and running on interface ppp0
> ppp0 Link encap:Point-to-Point Protocol
> inet addr:xxxxxxxxxxx P-t-P:10.0.0.3 Mask:255.255.255.255
> UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
> RX packets:2872 errors:0 dropped:0 overruns:0 frame:0
> TX packets:2789 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:3
> RX bytes:2549478 (2.4 MiB) TX bytes:361971 (353.4 KiB)
>

12. NOW you are CONNECTED but nothing happens!The solution:

Type: " route del default"
Then: " route add default ppp0"

NOW it should be working!
Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 1 of 1 [1 Post]  
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » House Training » HOWTO ( Solutions )
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0535s ][ Queries: 11 (0.0065s) ][ GZIP on ]