Installer internet.. (Ethernet xircom)
Try running this command before using the Network Wizard:
Then open up the network wizard and try again. That command should load the xircom_cb driver, which is not loaded according to the output of "lsmod".
D-Link is a brand name, so the router should prominently display the name on the its surface somewhere.
Code: Select all
# modprobe xircom_cb
D-Link is a brand name, so the router should prominently display the name on the its surface somewhere.
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath
-
- Posts: 74
- Joined: Sun 11 Dec 2005, 20:27
- Location: uk
the dsl photo shows that the driver being used is the xircom_tulip_cb. not the xircom_cb driver.[/quote]
You're correct. My faux pas. Both are loaded though, hmmm.
Noxx, run this command instead of what I said before:
Then use the network wizard as normal.
You're correct. My faux pas. Both are loaded though, hmmm.
Noxx, run this command instead of what I said before:
Code: Select all
# modprobe xircom_tulip_cb
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath
hey
i tried, unfortunately nothing change
I think this is a DHCP problem, maybe i should try to manually configure my Static IP. Already tried some things, 192.168.0.3 as IP, 255.255.255.0 as Netmask, 192.168.0.1 as Gateway and DNS, when i load a site in Seamonkey, instead of showing me an error page immediatly, we can see that the computer is searching for the page, and after the error page is desplayed.
i tried, unfortunately nothing change
I think this is a DHCP problem, maybe i should try to manually configure my Static IP. Already tried some things, 192.168.0.3 as IP, 255.255.255.0 as Netmask, 192.168.0.1 as Gateway and DNS, when i load a site in Seamonkey, instead of showing me an error page immediatly, we can see that the computer is searching for the page, and after the error page is desplayed.
Actually the IP you use will be dictated by the settings of your router. You should choose an IP that is in the same IP range (i.e.: 19.168.0.X) but is outside of the range the router is set to use (for instance, your router may be set up to only assign IPs between 192.168.0.1 and 192.168.0.9). If you can't log in to the router's administration utility, just anything within the proper range (192.168.0.X) that is not already in use by another machine on the network.
You will need to set your gateway to 192.168.0.255 and your net mask to 255.255.255.0, while leaving the DNS parameters blank (unless your ISP has specified DNS servers for you to use).
Bonne chance!
You will need to set your gateway to 192.168.0.255 and your net mask to 255.255.255.0, while leaving the DNS parameters blank (unless your ISP has specified DNS servers for you to use).
Bonne chance!
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath
Thanks, but still doesn't work
--> When i put Gateway 192.168.0.255 it says it dosen't exist, so as i think my router's IP is 192.168.0.1, that's what i put.
--> When i leave DNS blank, the internet site can't be found in .030 sec approximately. When i put 192.168.0.1 as DNS, it takes 6-7 before the error
Conclusion : i think i've gotta find my correct DNS server. a /ipconfig /all in windows shows me that my DNS server is 192.168.0.1
I think i'm gonna try SLAX or some other linux distro :p
Thank you at all, you were very helpful, and even if i didn't resolve my problem, i learned things :p that's what i like with computers ^^
Important edit : I installed Puppy 2.20 Community Edition, DHCP works, it shows "successfull", the only thing is that it doesn't connect, when i want to manually put an ip I can see that the DHCP sent wrong informations..
--> When i put Gateway 192.168.0.255 it says it dosen't exist, so as i think my router's IP is 192.168.0.1, that's what i put.
--> When i leave DNS blank, the internet site can't be found in .030 sec approximately. When i put 192.168.0.1 as DNS, it takes 6-7 before the error
Conclusion : i think i've gotta find my correct DNS server. a /ipconfig /all in windows shows me that my DNS server is 192.168.0.1
I think i'm gonna try SLAX or some other linux distro :p
Thank you at all, you were very helpful, and even if i didn't resolve my problem, i learned things :p that's what i like with computers ^^
Important edit : I installed Puppy 2.20 Community Edition, DHCP works, it shows "successfull", the only thing is that it doesn't connect, when i want to manually put an ip I can see that the DHCP sent wrong informations..
2.20 is an alpha version (it is not yet complete and full of bugs). It always says that getting a connection was successful even if it couldn't get an IP address. This should be fixed when Barry releases the beta version.
Sorry I couldn't help you more.
Sorry I couldn't help you more.
Be brave that God may help thee, speak the truth even if it leads to death, and safeguard the helpless. - A knight's oath