Still working for me!
I haven't had a chance to really stress test it, but the new install works nicely.
You might want to have the script check for "manuwifi" and offer to copy it if present (assuming that there will be more upgrades on the program). It's not hard to recreate it, but probably not hard to store it, either.
WAG-0.2.2.pup Wireless Access Gadget
I am on the 770z with the orinoco classic gold card and it sees the connection now but still dosn't treat it as wireless. Won't scan with this card. I tried the new one on the 600e with the linksys wpc11 v4 running wifi-pup and it found my network and my neighbors too. I could not however connect to either one as dhcp wouldn't work. It also reported signal at 0/100. I will try another card and see what happens on the E when I get a few minutes. Running 1.0.3 on this one still.
Code: Select all
wireless card not active
wireless card not responding
no module loaded
dhcpcd running
wifi-beta installed
eth0 enabled
no IP assigned to eth0
access point aquired
no internet ping test
0 wireless network(s) detected
0 open network(s) detected
Connected to:
eth0 IEEE 802.11-DS ESSID:"home" Nickname:"HERMES I"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Encryption key:off
Link Quality:54/92 Signal level:-44 dBm Noise level:-98 dBmPuppy Linux...
It just works!
It just works!
From the 600e with the linksys card.
I will see what others might work.
Code: Select all
wireless card not active
wireless card not responding
no module loaded
dhcpcd running
wifi-beta installed
wlan0 enabled
no IP assigned to wlan0
access point aquired
internet ping sucessful
1 wireless network(s) detected
1 open network(s) detected
Connected to:
wlan0 IEEE 802.11b ESSID:"home" Nickname:"puppylaptop"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Encryption key:off
Link Quality:100/100 Signal level:-58 dBm Noise level:-256 dBmPuppy Linux...
It just works!
It just works!
I also have an orinoco a/b proxim wavelan 2cs.4 that runs on this Called a "combocard Gold" part# 8460-05. I was about to post the results from this one and I realized that wasn't what you were looking for. Well, while I am on a run.
Code: Select all
wireless card not active
wireless card not responding
no module loaded
dhcpcd running
wifi-beta installed
wlan0 enabled
no IP assigned to wlan0
access point aquired
internet ping sucessful
0 wireless network(s) detected
0 open network(s) detected
Connected to:
wlan0 IEEE 802.11b ESSID:"home" Nickname:"puppylaptop"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Encryption key:off
Link Quality:50/100 Signal level:-50 dBm Noise level:-256 dBmPuppy Linux...
It just works!
It just works!
I got 3 out of 4 working, gave up on the gigafast.
Here is the results.
results from the new orinoco combocard.
_____________AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
wlan0 Link encap:Ethernet HWaddr 00:20:A6:4C:17:A0
inet addr:192.168.1.8 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:802 errors:0 dropped:0 overruns:0 frame:0
TX packets:835 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:601367 (587.2 kiB) TX bytes:120398 (117.5 kiB)
Memory:10c00000-10c0ffff
IWCONFIG
wlan0 IEEE 802.11b ESSID:"home" Nickname:"puppylaptop"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate=11Mb/s
Encryption key:off
Link Quality:48/100 Signal level:-53 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
wlan0 No scan results
IWLIST AP
PING
PING google.com (216.239.37.99): 56 data bytes
--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 75.6/75.6/75.6 ms
LSMOD
Module Size Used by Not tainted
cs4232 3748 0 (unused)
uart401 6180 0 [cs4232]
ad1848 22060 0 [cs4232]
sound 55112 0 [cs4232 uart401 ad1848]
soundcore 3588 4 [sound]
ndiswrapper 105076 1
parport_pc 15108 0
parport 23880 0 [parport_pc]
sr_mod 14488 0 (unused)
ide-cd 29504 0
cdrom 27744 0 [sr_mod ide-cd]
sd_mod 11404 0 (unused)
ds 6580 2
yenta_socket 10436 2
pcmcia_core 40228 0 [ds yenta_socket]
usb-uhci 21936 0 (autoclean) (unused)
usbcore 59596 1 (autoclean) [ndiswrapper usb-uhci]
scsi_mod 93972 2 [sr_mod sd_mod]
DHCPCD
242 root 1464 S dhcpcd wlan0
CARDCTL STATUS
Socket 0:
no card
Socket 1:
3.3V CardBus card
function 0: [ready]
CARDCTL IDENT
Socket 0:
no product info available
Socket 1:
product info: "Atheros Communications, Inc.", "AR5001-0000-0000", "Wireless LAN Reference Card", "00"
manfid: 0x0271, 0x0012
function: 6 (network)
_________________________________
Here is the linksys wpc11 v4
AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
wlan0 Link encap:Ethernet HWaddr 00:13:10:66:B7:4D
inet addr:192.168.1.9 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2022 (1.9 kiB) TX bytes:2756 (2.6 kiB)
Memory:10c00000-10c000ff
IWCONFIG
wlan0 IEEE 802.11b ESSID:"home" Nickname:"puppylaptop"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate=11Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr=2432 B Fragment thr=2432 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-49 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
wlan0 Scan completed :
Cell 01 - Address: 00:E0:98:DE:D3:33
ESSID:"home"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.447GHz
Quality:0/100 Signal level:-49 dBm Noise level:-256 dBm
Encryption key:off
Bit Rate:1Mb/s
Bit Rate:2Mb/s
Bit Rate:5.5Mb/s
Bit Rate:11Mb/s
Extra:bcn_int=100
Extra:atim=0
IWLIST AP
PING
PING google.com (216.239.37.99): 56 data bytes
--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 79.3/79.3/79.3 ms
LSMOD
Module Size Used by Not tainted
cs4232 3748 0 (unused)
uart401 6180 0 [cs4232]
ad1848 22060 0 [cs4232]
sound 55112 0 [cs4232 uart401 ad1848]
soundcore 3588 4 [sound]
ndiswrapper 105076 1
parport_pc 15108 0
parport 23880 0 [parport_pc]
sr_mod 14488 0 (unused)
ide-cd 29504 0
cdrom 27744 0 [sr_mod ide-cd]
sd_mod 11404 0 (unused)
ds 6580 2
yenta_socket 10436 2
pcmcia_core 40228 0 [ds yenta_socket]
usb-uhci 21936 0 (autoclean) (unused)
usbcore 59596 1 (autoclean) [ndiswrapper usb-uhci]
scsi_mod 93972 2 [sr_mod sd_mod]
DHCPCD
237 root 1464 S dhcpcd wlan0
CARDCTL STATUS
Socket 0:
no card
Socket 1:
3.3V CardBus card
function 0: [ready]
CARDCTL IDENT
Socket 0:
no product info available
Socket 1:
product info: "Realtek", "Rtl8139"
manfid: 0x0000, 0x024c
function: 6 (network)
__________________________
Here is the orinoco classic gold
AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
eth0 Link encap:Ethernet HWaddr 00:02:2D:AB:30:2F
inet addr:192.168.1.1 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:1 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:336 (336.0 iB) TX bytes:758 (758.0 iB)
Interrupt:3 Base address:0x180
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
IWCONFIG
eth0 IEEE 802.11-DS ESSID:"home" Nickname:"HERMES I"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate:11Mb/s Tx-Power=15 dBm Sensitivity:1/3
Retry limit:4 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:62/92 Signal level:-33 dBm Noise level:-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
IWLIST AP
PING
PING google.com (216.239.57.99): 56 data bytes
--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 142.5/142.5/142.5 ms
LSMOD
Module Size Used by Not tainted
orinoco_cs 4244 1
orinoco 32436 0 [orinoco_cs]
hermes 5732 0 [orinoco_cs orinoco]
cs4232 3748 0 (unused)
uart401 6180 0 [cs4232]
ad1848 22060 0 [cs4232]
sound 55112 0 [cs4232 uart401 ad1848]
soundcore 3588 4 [sound]
ndiswrapper 105076 0
parport_pc 15108 0
parport 23880 0 [parport_pc]
sr_mod 14488 0 (unused)
ide-cd 29504 0
cdrom 27744 0 [sr_mod ide-cd]
sd_mod 11404 0 (unused)
ds 6580 2 [orinoco_cs]
yenta_socket 10436 2
pcmcia_core 40228 0 [orinoco_cs ds yenta_socket]
usb-uhci 21936 0 (autoclean) (unused)
usbcore 59596 1 (autoclean) [ndiswrapper usb-uhci]
scsi_mod 93972 2 [sr_mod sd_mod]
DHCPCD
237 root 1464 S dhcpcd wlan0
798 root 1468 S dhcpcd -d eth0
CARDCTL STATUS
Socket 0:
no card
Socket 1:
5V 16-bit PC Card
function 0: [ready]
CARDCTL IDENT
Socket 0:
no product info available
Socket 1:
product info: "Lucent Technologies", "WaveLAN/IEEE", "Version 01.01", ""
manfid: 0x0156, 0x0002
function: 6 (network)
Here is the results.
results from the new orinoco combocard.
_____________AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
wlan0 Link encap:Ethernet HWaddr 00:20:A6:4C:17:A0
inet addr:192.168.1.8 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:802 errors:0 dropped:0 overruns:0 frame:0
TX packets:835 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:601367 (587.2 kiB) TX bytes:120398 (117.5 kiB)
Memory:10c00000-10c0ffff
IWCONFIG
wlan0 IEEE 802.11b ESSID:"home" Nickname:"puppylaptop"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate=11Mb/s
Encryption key:off
Link Quality:48/100 Signal level:-53 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
wlan0 No scan results
IWLIST AP
PING
PING google.com (216.239.37.99): 56 data bytes
--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 75.6/75.6/75.6 ms
LSMOD
Module Size Used by Not tainted
cs4232 3748 0 (unused)
uart401 6180 0 [cs4232]
ad1848 22060 0 [cs4232]
sound 55112 0 [cs4232 uart401 ad1848]
soundcore 3588 4 [sound]
ndiswrapper 105076 1
parport_pc 15108 0
parport 23880 0 [parport_pc]
sr_mod 14488 0 (unused)
ide-cd 29504 0
cdrom 27744 0 [sr_mod ide-cd]
sd_mod 11404 0 (unused)
ds 6580 2
yenta_socket 10436 2
pcmcia_core 40228 0 [ds yenta_socket]
usb-uhci 21936 0 (autoclean) (unused)
usbcore 59596 1 (autoclean) [ndiswrapper usb-uhci]
scsi_mod 93972 2 [sr_mod sd_mod]
DHCPCD
242 root 1464 S dhcpcd wlan0
CARDCTL STATUS
Socket 0:
no card
Socket 1:
3.3V CardBus card
function 0: [ready]
CARDCTL IDENT
Socket 0:
no product info available
Socket 1:
product info: "Atheros Communications, Inc.", "AR5001-0000-0000", "Wireless LAN Reference Card", "00"
manfid: 0x0271, 0x0012
function: 6 (network)
_________________________________
Here is the linksys wpc11 v4
AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
wlan0 Link encap:Ethernet HWaddr 00:13:10:66:B7:4D
inet addr:192.168.1.9 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2022 (1.9 kiB) TX bytes:2756 (2.6 kiB)
Memory:10c00000-10c000ff
IWCONFIG
wlan0 IEEE 802.11b ESSID:"home" Nickname:"puppylaptop"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate=11Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr=2432 B Fragment thr=2432 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-49 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
wlan0 Scan completed :
Cell 01 - Address: 00:E0:98:DE:D3:33
ESSID:"home"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.447GHz
Quality:0/100 Signal level:-49 dBm Noise level:-256 dBm
Encryption key:off
Bit Rate:1Mb/s
Bit Rate:2Mb/s
Bit Rate:5.5Mb/s
Bit Rate:11Mb/s
Extra:bcn_int=100
Extra:atim=0
IWLIST AP
PING
PING google.com (216.239.37.99): 56 data bytes
--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 79.3/79.3/79.3 ms
LSMOD
Module Size Used by Not tainted
cs4232 3748 0 (unused)
uart401 6180 0 [cs4232]
ad1848 22060 0 [cs4232]
sound 55112 0 [cs4232 uart401 ad1848]
soundcore 3588 4 [sound]
ndiswrapper 105076 1
parport_pc 15108 0
parport 23880 0 [parport_pc]
sr_mod 14488 0 (unused)
ide-cd 29504 0
cdrom 27744 0 [sr_mod ide-cd]
sd_mod 11404 0 (unused)
ds 6580 2
yenta_socket 10436 2
pcmcia_core 40228 0 [ds yenta_socket]
usb-uhci 21936 0 (autoclean) (unused)
usbcore 59596 1 (autoclean) [ndiswrapper usb-uhci]
scsi_mod 93972 2 [sr_mod sd_mod]
DHCPCD
237 root 1464 S dhcpcd wlan0
CARDCTL STATUS
Socket 0:
no card
Socket 1:
3.3V CardBus card
function 0: [ready]
CARDCTL IDENT
Socket 0:
no product info available
Socket 1:
product info: "Realtek", "Rtl8139"
manfid: 0x0000, 0x024c
function: 6 (network)
__________________________
Here is the orinoco classic gold
AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
eth0 Link encap:Ethernet HWaddr 00:02:2D:AB:30:2F
inet addr:192.168.1.1 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:1 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:336 (336.0 iB) TX bytes:758 (758.0 iB)
Interrupt:3 Base address:0x180
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
IWCONFIG
eth0 IEEE 802.11-DS ESSID:"home" Nickname:"HERMES I"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate:11Mb/s Tx-Power=15 dBm Sensitivity:1/3
Retry limit:4 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:62/92 Signal level:-33 dBm Noise level:-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
IWLIST AP
PING
PING google.com (216.239.57.99): 56 data bytes
--- google.com ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 142.5/142.5/142.5 ms
LSMOD
Module Size Used by Not tainted
orinoco_cs 4244 1
orinoco 32436 0 [orinoco_cs]
hermes 5732 0 [orinoco_cs orinoco]
cs4232 3748 0 (unused)
uart401 6180 0 [cs4232]
ad1848 22060 0 [cs4232]
sound 55112 0 [cs4232 uart401 ad1848]
soundcore 3588 4 [sound]
ndiswrapper 105076 0
parport_pc 15108 0
parport 23880 0 [parport_pc]
sr_mod 14488 0 (unused)
ide-cd 29504 0
cdrom 27744 0 [sr_mod ide-cd]
sd_mod 11404 0 (unused)
ds 6580 2 [orinoco_cs]
yenta_socket 10436 2
pcmcia_core 40228 0 [orinoco_cs ds yenta_socket]
usb-uhci 21936 0 (autoclean) (unused)
usbcore 59596 1 (autoclean) [ndiswrapper usb-uhci]
scsi_mod 93972 2 [sr_mod sd_mod]
DHCPCD
237 root 1464 S dhcpcd wlan0
798 root 1468 S dhcpcd -d eth0
CARDCTL STATUS
Socket 0:
no card
Socket 1:
5V 16-bit PC Card
function 0: [ready]
CARDCTL IDENT
Socket 0:
no product info available
Socket 1:
product info: "Lucent Technologies", "WaveLAN/IEEE", "Version 01.01", ""
manfid: 0x0156, 0x0002
function: 6 (network)
Puppy Linux...
It just works!
It just works!
-
keenerd
Peppyy, thank you for that info. I will add support for Nicknames and some other details of your hardware.
But first, could you please properly configure WAG? You have plugged all your cards into socket 1. WAG defaults to socket zero, and it isn't smart enough to auto detect the socket. I'll work on that. Until then, could you open /root/my-roxapps/WAG/AppRun in a text editor. Near the top there is a line which says
CARDSOC="0"
Change this to say
CARDSOC="1"
Or just start using your cards in the other socket, which is empty. (Of course, don't do both or you're right back to where you started)
If you don't do either of these, it will always say card not active/responding, and half of WAG's functions will not work properly.
But first, could you please properly configure WAG? You have plugged all your cards into socket 1. WAG defaults to socket zero, and it isn't smart enough to auto detect the socket. I'll work on that. Until then, could you open /root/my-roxapps/WAG/AppRun in a text editor. Near the top there is a line which says
CARDSOC="0"
Change this to say
CARDSOC="1"
Or just start using your cards in the other socket, which is empty. (Of course, don't do both or you're right back to where you started)
If you don't do either of these, it will always say card not active/responding, and half of WAG's functions will not work properly.
I am so sorry. I stayed up way too late and must have missed that somehow. Amazing, I can actually connect like I should with the card in the top socket.
Here is the linksys in cardsoc0
AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
wlan0 Link encap:Ethernet HWaddr 00:13:10:66:B7:4D
inet addr:192.168.1.9 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:280 errors:0 dropped:0 overruns:0 frame:0
TX packets:312 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:183195 (178.9 kiB) TX bytes:48750 (47.6 kiB)
Memory:10400000-104000ff
IWCONFIG
wlan0 IEEE 802.11b ESSID:"home"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate:11Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr:2432 B Fragment thr:2432 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-51 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
Here is the linksys in cardsoc0
AUTOWIFI
#!/bin/sh
# this script is user specific and may be optional
# it is called as the final step of the Reseat and scan process
# if you have extra steps to activate a wireless connection,
# append them here
MANUWIFI
#!/bin/sh
# If the autowifi script isn't sufficient,
# or you need to run random commands at random times
# then place those commands here
# they will be run whenever you press the custom button
iwconfig wlan0 key *** essid *** mode managed channel **
IFCONFIG
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 iB) TX bytes:0 (0.0 iB)
wlan0 Link encap:Ethernet HWaddr 00:13:10:66:B7:4D
inet addr:192.168.1.9 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:280 errors:0 dropped:0 overruns:0 frame:0
TX packets:312 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:183195 (178.9 kiB) TX bytes:48750 (47.6 kiB)
Memory:10400000-104000ff
IWCONFIG
wlan0 IEEE 802.11b ESSID:"home"
Mode:Managed Frequency:2.447GHz Access Point: 00:E0:98:DE:D3:33
Bit Rate:11Mb/s Tx-Power:20 dBm Sensitivity=0/3
RTS thr:2432 B Fragment thr:2432 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-51 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
IWLIST SCAN
Puppy Linux...
It just works!
It just works!
I really like this forum. I think its a very nice place. Case in point, for weeks I have been posting on this board. I've uploaded files. All without an account. Its an amazing feature that more places should allow. Sure, you run the risk of being spammed, but its nice that a newbie who will only ever post one question doesn't have to go an register a unique username and password.
But the unregistered "non-citizens" don't have any rights. Free speech certainly, but they can be edited at a whim. Sometimes, this is a good thing. One of my first posts was had a horribly nondescript title. A moderator fixed it. Good use of power. But now someone has gone and changed the name of my program. And while I am not the most creative person, I will take suggestions. Polite suggestions from sources I can see. Not strong armed manipulation that happens without warning. Moderators (and the like) should always be curteous and say why they change someone's post, even for legitimate reasons. At least mention it when someone's program is renamed from Wireless Access Gadget to Wireless Access Grabber. I appreciate the more descriptive subject line, but I prefer a truthful one.
I'm not mad, just annoyed. But now you've gone and made me register. So, now that I'm a registered "citizen", can someone fix it?
Onto the serious portion:
Peppy, thank you for all the data. I'll look for an alternative to "iwlist scan". That one command is the underpinning of the whole program. Support varies, even between drivers. My card supports scanning under Madwifi but not under Ndiswrapper. Linked man pages suggest more options, but not all of the commands are included with Puppy.
But the unregistered "non-citizens" don't have any rights. Free speech certainly, but they can be edited at a whim. Sometimes, this is a good thing. One of my first posts was had a horribly nondescript title. A moderator fixed it. Good use of power. But now someone has gone and changed the name of my program. And while I am not the most creative person, I will take suggestions. Polite suggestions from sources I can see. Not strong armed manipulation that happens without warning. Moderators (and the like) should always be curteous and say why they change someone's post, even for legitimate reasons. At least mention it when someone's program is renamed from Wireless Access Gadget to Wireless Access Grabber. I appreciate the more descriptive subject line, but I prefer a truthful one.
I'm not mad, just annoyed. But now you've gone and made me register. So, now that I'm a registered "citizen", can someone fix it?
Onto the serious portion:
Peppy, thank you for all the data. I'll look for an alternative to "iwlist scan". That one command is the underpinning of the whole program. Support varies, even between drivers. My card supports scanning under Madwifi but not under Ndiswrapper. Linked man pages suggest more options, but not all of the commands are included with Puppy.
I'm afraid it was me who did that, and it was a mistake. I didn't mean to change the name you gave it, only expand the "wag" in the subject line so it would catch the eye. I wasn't paying attention, apparently. I'm terribly sorry.keenerd wrote:"...someone has gone and changed the name of my program. And while I am not the most creative person, I will take suggestions. Polite suggestions from sources I can see. Not strong armed manipulation that happens without warning. Moderators (and the like) should always be curteous and say why they change someone's post, even for legitimate reasons. At least mention it when someone's program is renamed from Wireless Access Gadget to Wireless Access Grabber. I appreciate the more descriptive subject line, but I prefer a truthful one.
Now that you've registered, I find that I can't correct my mistake. As the registered originator of that post, so you should be able to change it yourself.
WAG-0.2.4.pup Wireless Access Gadget
Flash, no hard feelings.
Testers of WAG-0.2.4: I have found a very small bug. I messed up* some quotes, so you'll have trouble connecting to access points with spaces in the name. Here's how to fix:
Open the WAG AppRun in a text editor.
Do find a find and replace.
Find:
essid $SCANESSID
and replace it with:
essid "$SCANESSID"
Click replace all, and save the change.
There is exactly one occurance, so its easy.
*It looks like I forgot them, but I think the iwconfig docs are incorrect. They show the essid option working without quotes and with spaces in the name. Yesterday I tested on an AP with spaces, and iwconfig clipped the essid at the first space.
Testers of WAG-0.2.4: I have found a very small bug. I messed up* some quotes, so you'll have trouble connecting to access points with spaces in the name. Here's how to fix:
Open the WAG AppRun in a text editor.
Do find a find and replace.
Find:
essid $SCANESSID
and replace it with:
essid "$SCANESSID"
Click replace all, and save the change.
There is exactly one occurance, so its easy.
*It looks like I forgot them, but I think the iwconfig docs are incorrect. They show the essid option working without quotes and with spaces in the name. Yesterday I tested on an AP with spaces, and iwconfig clipped the essid at the first space.
WAG-0.2.4.pup Wireless Access Gadget
Flash, it seems I'm stuck. You change the subject by changing the subject of the post which started the thread, right? Well, I can only edit my own messages. After registering. Registering gives me no retroactive powers over previous anonymous posts which just happen to have the same name as me. So, I can't change the subject it.
I've tried a bunch of other stuff, too.
I've tried a bunch of other stuff, too.