(old)Puppy Linux Discussion Forum

Posted: **Fri 19 Oct 2018, 12:32**

CLOSED - see UPupDD Disco Dingo

UPupCC-18.10+18-uefi

http://murga-linux.com/puppy/viewtopic. ... 44#1020144

Ubuntu Cosmic Cuttlefish components
Woof-CE testing branch
Kernel 4.9.134 32-bit pae
Same app mix as UPupBB

Note: Cosmic Cuttlefish will become unsupported by Ubuntu after July 2019

Posted: **Fri 19 Oct 2018, 12:32**

Deltas can also be converted to pets with this utility.

Posted: **Fri 19 Oct 2018, 12:33**

reserved

Posted: **Fri 19 Oct 2018, 14:44**

Thanks for your endless effort to give us the goodies!

Tested this on my new Lenovo yoga 530, and did not boot into X.
Do you plan to offer newer kernels?

Posted: **Fri 19 Oct 2018, 14:51**

I installed to a 64gb Sandisk flash drive:

System: Host: puppypc3397 Kernel: 4.9.134-lxpup-32-pae i686 (32 bit) Desktop: JWM 2.3.7 Distro: UPupCC 18.10
Machine: Device: desktop System: Compaq-Presario product: AU194AA-A2L CQ5123F serial: MXX9300M0F
Mobo: MSI model: Boston v: 1.0 BIOS: Phoenix v: 5.24 date: 06/19/2009
CPU: Dual core Pentium E5200 (-MCP-) speed/max: 2000/2500 MHz
Graphics: Card: Advanced Micro Devices [AMD/ATI] RV530 [Radeon X1600 PRO]
Display Server: X.org 1.20.1 drivers: ati,radeon (unloaded: modesetting,fbdev,vesa,intel)
tty size: 147x24 Advanced Data: N/A for root
Network: Card: Realtek RTL810xE PCI Express Fast Ethernet controller driver: r8169
Drives: HDD Total Size: 563.2GB (0.9% used)
Weather: Conditions: 48 F (9 C) - Mostly Cloudy Time: October 19, 10:45 AM EDT
Info: Processes: 160 Uptime: 8 min Memory: 151.1/4035.2MB Client: Shell (bash) inxi: 2.3.8

Updated PPM and added Kodi,Vlc,Smplayer-Smtube,Kpat.
It's working well,
Thanks.

Posted: **Fri 19 Oct 2018, 14:55**

zigbert wrote:Thanks for your endless effort to give us the goodies!

Tested this on my new Lenovo yoga 530, and did not boot into X.
Do you plan to offer newer kernels?

Try 4.18.15 64-bit from:
https://sourceforge.net/projects/lxpup/ ... /interims/
??

Posted: **Fri 19 Oct 2018, 17:01**

upupcc 18.10 beta 1 updated to 18.10 on this hardware, Grub4Dos frugal install to SSD with 256Mb EXT2 savefile. :

Code: Select all

System:    Host: puppypc20747 Kernel: 4.9.134-lxpup-32-pae i686 bits: 32
           Desktop: JWM 2.3.7 Distro: UPupCC 18.10
Machine:   Device: laptop System: FUJITSU product: LIFEBOOK S761 serial: R2500459
           Mobo: FUJITSU model: FJNB225 serial: N/A
           UEFI [Legacy]: FUJITSU // Phoenix v: Version 1.17 date: 03/14/2012
Battery    CMB1: charge: 46.9 Wh 91.0% condition: 51.5/62.2 Wh (83%)
CPU:       Dual core Intel Core i5-2520M (-HT-MCP-) speed/max: 801/3200 MHz
Graphics:  Card: Intel 2nd Generation Core Integrated Graphics Controller
           Display Server: X.Org 1.20.1
           drivers: modesetting (unloaded: fbdev,vesa)
           Resolution: 1366x768@60.00hz
           OpenGL: renderer: Mesa DRI Intel Sandybridge Mobile x86/MMX/SSE2
           version: 3.3 Mesa 18.2.2
Network:   Card: Qualcomm Atheros AR9287 Wireless Network Adapter (PCI-Express)
           driver: ath9k
Drives:    HDD Total Size: 120.0GB (36.9% used)
Weather:   Conditions: 48 F (9 C) - Overcast Time: October 19, 11:45 AM CDT
Info:      Processes: 176 Uptime: 15 min Memory: 111.4/4881.5MB
           Client: Shell (bash) inxi: 2.3.40

Dmesg continues to be clean except for these:

Code: Select all

udevd[3253]: Process '/sbin/pup_event_backend_modprobe' failed with exit code 1.

Drive mounting and reporting is all working correctly...

Video performance, CPU and mem use at idle, sound, SNS connection all continue to be great on this series of middle-aged laptops. The 4.18.15 64b kernel is downloaded. I'll test that first in lxpupsc64, then in the upups.

Thanks,

Posted: **Fri 19 Oct 2018, 18:04**

Working well with my old laptop in my usual frugal install:

Code: Select all

./inxi_git2018 -Fxx
System:
  Host: puppypc32209 Kernel: 4.9.134-lxpup-32-pae i686 bits: 32 
  compiler: gcc v: 8.2.0 Desktop: JWM 2.3.7 dm: xinit Distro: Puppy 18.10 
Machine:
  Type: Laptop System: Hewlett-Packard product: HP 550 v: F.02 
  serial: CNU83643ZG Chassis: type: 10 serial: CNU83643ZG 
  Mobo: Hewlett-Packard model: 3618 v: KBC Version 12.00 serial: N/A 
  BIOS: Hewlett-Packard v: 68MVU Ver. F.02 date: 08/20/2008 
Battery:
  ID-1: C23B charge: 29.8 Wh condition: 30.1/30.1 Wh (100%) volts: 12.4/10.8 
  model: Hewlett-Packard Primary serial: 01052 2008/08/22 status: Unknown 
CPU:
  Topology: Single Core model: Intel Celeron 530 bits: 64 type: MCP 
  arch: Core Merom rev: 1 L1 cache: 64 KiB L2 cache: 1024 KiB 
  flags: lm nx pae sse sse2 sse3 ssse3 bogomips: 3458 
  Speed: 1733 MHz min/max: 217/1733 MHz Core speed (MHz): 1: 1733 
Graphics:
  Device-1: Intel Mobile GME965/GLE960 Integrated Graphics driver: i915 
  v: kernel bus ID: 00:02.0 chip ID: 8086:2a12 
  Display: server: X.Org 1.20.1 driver: modesetting unloaded: fbdev,vesa 
  resolution: 1280x800~60Hz 
  OpenGL: renderer: Mesa DRI Intel 965GME/GLE x86/MMX/SSE2 
  v: 2.1 Mesa 18.2.2 direct render: Yes 
Audio:
  Device-1: Intel 82801H HD Audio driver: snd_hda_intel v: kernel 
  bus ID: 00:1b.0 chip ID: 8086:284b 
  Sound Server: ALSA v: k4.9.134-lxpup-32-pae 
Network:
  Device-1: Intel 82562GT 10/100 Network driver: e1000e v: 3.2.6-k 
  port: 4020 bus ID: 00:19.0 chip ID: 8086:10c4 
  IF: eth0 state: up speed: 100 Mbps duplex: full mac: 00:22:64:4a:70:62 
  Device-2: Broadcom and subsidiaries BCM4312 802.11b/g LP-PHY 
  driver: b43-pci-bridge v: N/A port: 4100 bus ID: 10:00.0 
  chip ID: 14e4:4315 
  IF-ID-1: wlan0 state: down mac: 00:21:00:5b:0a:06 
Drives:
  Local Storage: total: 260.84 GiB used: 191.51 GiB (73.4%) 
  ID-1: /dev/sda vendor: Hitachi model: HTS54251 size: 111.79 GiB 
  speed: 3.0 Gb/s serial: N/A 
  ID-2: /dev/sdb model: USB Disk size: 149.05 GiB serial: N/A 
Partition:
  ID-1: swap-1 size: 1000.0 MiB used: 0 KiB (0.0%) fs: swap dev: /dev/sda2 
Sensors:
  Missing: Required tool sensors not installed. Check --recommends 
Info:
  Processes: 164 Uptime: 15m Memory: 1.46 GiB used: 373.9 MiB (25.0%) 
  Init: SysVinit v: N/A runlevel: 35 Compilers: gcc: N/A alt: 7 Shell: bash 
  v: 4.4.19 running in: lxterminal inxi: 3.0.26

Posted: **Fri 19 Oct 2018, 20:00**

After beta1 (ie b2, 3 and this one) the ISOs do not boot for me on a VM.
Frugal install works fine on the same VMs
Anybody booted successfully from the ISO on a physical or virtual machine?

Posted: **Fri 19 Oct 2018, 20:41**

I've somehow managed to miss the alpha and beta ISos - I am a shamed

if anybody has them please can you drop them here: https://drive.google.com/drive/folders/ ... sp=sharing so I can put them on the archive

ta

edit - link corrected

Posted: **Fri 19 Oct 2018, 20:53**

With kernel 4.18.15, it boots to desktop. Great!
Thanks a lot!

But, there is a lot not working... touchpad, touchscreen, cputemp, function-keys (backlight), HDMI output, wifi, and probably more...

For me, the most important is external screen and wifi.
I guess the HDMI requires a updated firmware for AMD Vega 8... (Ryzen 5 2500u)
Wifi: Realtek RTL8821CE

Any help is appreciated

Posted: **Fri 19 Oct 2018, 21:29**

Posted: **Sat 20 Oct 2018, 09:04**

Update 18.10+1 has fixes for syslinux and ppm

Posted: **Sat 20 Oct 2018, 09:56**

peebee wrote:Update 18.10+1 has fixes for syslinux

The ISO boots fine now.

Another thing you may want to pay attention to is dbus and X.
X complains about not finding data for libinput and dbus-core floods the Xorg.log with missing /var/run/dbus/system_bus_socket messages (indeed is missing).
As a result X functionality is very limited.

Posted: **Sat 20 Oct 2018, 14:12**

mavrothal wrote:Another thing you may want to pay attention to is dbus and X.

Thanks @mav

18.10+1 reuploaded with a fix - directory /run/dbus needed to be created before dbus started.

Posted: **Sat 20 Oct 2018, 18:00**

I tried to compile adbfs-rootless and it fails claiming g++ is missing. A symlink to g++-7 does the trick.

Posted: **Sun 21 Oct 2018, 10:18**

Thanks @watchdog....

devx was "malformed"

now rebuilt and re-uploaded....now gcc-8

Posted: **Mon 22 Oct 2018, 05:45**

G'day peebee,

So nice to try a new 32-bit Puppy in which most things 'just work' for me, after my on-going hassles with several 64-bit Pups, mostly with scanning and printing, plus various apps which need libs in different places for different Pups.

Anyway, back on-topic......
... all my sfs-added apps look to be running and I can print and scan on my networked Epson WF-2510.
One difference to me is the testprint page which has a Pup logo

but the colour swatches are over some text - still readable but a little messy (screenshot).

Only problem I've come across is the module to monitor my computer temperatures is not loading. I've copied the MODULESCONFIG textfile in /etc/rc.d/ that has the needed module line and the module is listed in the Boot Manager as well.

But running sensors says no modules are loaded, and Pwidgets is blank in its Temp-CPU widgets (screenshot).
This has worked in all previous Pups so I'm puzzled.

Thanks for all your work,

David S.

Posted: **Mon 22 Oct 2018, 13:15**

davids45 wrote:Only problem I've come across is the module to monitor my computer temperatures is not loading.
David S.

Hi DavidS

The temperature icon never appears on first boot (known "feature") - it can be made to appear by doing an XServer (Graphical manager) restart. Or a reboot + savespace creation.

If you hover your mouse over the blank space in the systray you will probably see cpu details....

Posted: **Mon 22 Oct 2018, 21:42**

G'day peebee,

Thanks for your reply about my Cuttlefish's lack of CPU data.

It's not just the tray temperature that I'm missing but also the more details that come up in my CPU-Temp widget.

Screenshots show Bionic with the smsc47b397 module running (info in widgets and tray) and Cosmic with nothing even after several re-boots.

The module ( smsc47b397 ) needed in my HP Small-form desktops is listed in the /etc/rc.d/MODULESCONFIG file and is working in all my other Pups.
In most other Pups, the tray temp needs the module loaded to display a temperature or a 'doesn't work on my system' message pops up.

Could I try this module from bionic in cosmic? (if I knew where to look

.)

David S.

(old)Puppy Linux Discussion Forum

32-bit UPup Cosmic Cuttlefish 18.10 (Oct 2018) [CLOSED]

32-bit UPup Cosmic Cuttlefish 18.10 (Oct 2018) [CLOSED]

Updates

Reserved

UPup Cosmic Cuttlefish (UPupCC) 18.10 (Oct 2018)

Module (CPU Temperature) not loading

Re: Module (CPU Temperature) not loading

Module for CPU data