(old)Puppy Linux Discussion Forum

I found this here on the puppy forum....can't remember where.

This might apply or not but at least should be innocuous and worth trying.
I had similar problems with my laptop equipped with bcm43xx and ubuntu, and in order to have wi-fi connection standing I had to boot with the following boot parameters (which here I report adapted to puppy linux):
Code:
puppy acpi=strict acpi=noirq pci=biosirq pci=nosort irqpoll routeirq


I hope this helps

Thank you.

I am using USB flash drive, so I edited syslinux.cfg based on a posting elsewhere in the forum http://www.murga-linux.com/puppy/search ... 6&start=15

I added the additional instructions:

default vmlinuz root=/dev/ram0 initrd=initrd.gz PMEDIA=usbflash acpi=strict acpi=noirq pci=biosirq pci=nosort irqpoll routeirq

I rebooted and I still cannot turn the wifi on the machiine. I loaded ipw2200, and still get the same err msg.

SH

Hi

Anyone managed to get a Wireless Buffalo Air Station WLI-CB-G54 WORKING. It's a PCMCIA card.

Thanks

Puppy Linux is great! I was able to get my Linksys WPC54GX working by using ndiswrapper and the driver/inf files off of the original CD--for some reason, the driver download from the Linksys site didn't work for me.

This is all wonderful information, though has grown to a point of needing some compilation in the interest of being even more valuable than it already is. I have no experience in setting such up, but here's what I'm envisioning, should some benevolent soul desire to build such a thing:

A chart with wifi card manufacturer/model/chipset in the left-hand column - in alpha-numeric order, top to bottom; Puppy version numbers across the top row; and both driver number and either "Linux" or "ndis" in the appropriate crosshatch boxes.

Linux/ndis could be omitted were an appropriate two-color scheme and key applied to the driver number.

Any takers?

-aj

Something like a spreadsheet wiki? Lobster might know of such a thing.

cobelloy wrote: netgear wg511v3 - ndiswrapper

Netgear WG511 v2 (made in China) also works fine, using ndiswrapper and the W2K drivers. From memory, the v2 (made in China) uses a Marvell chipset. (The Netgear cards are often available as a bundle with some Netgear routers, for little more than the cost of the router alone.)

Also working via ndiswrapper is the wireless LAN side of my Sony-Ericsson GC79 GPRS/WLAN card (Broadcom chipset). Apparently it's also possible to get the GPRS side working under Linux, but I haven't attempted that yet.

Using WPA1 with both of the above.

After spending up to 3 days on some other mini-distros trying to get my home network connection running on my dell inspiron 6400, i was getting depressed.

Puppy had the inbuilt wireless (intell PRO/Wireless 3954ABG) going in all of 5 minutes. Now that is user-friendliness right there.

Hi all,
I was trying to get a D-Link 650 vP pcmcia card to work, but no luck yet. However I was letting my daughter use a Netopia 3D reach USB. On Puppy 2.14 and now 2.16 wizard usedthe rt2570 driver worked first time. The box is a toshiba satellite 1715. Using the live CD. This a new cheap one frm china.
Joewilly

The Zyxel ZD1201 chipset-based USB wireless "dongles" also work with puppy, however you have to download the firmware (just google it!) and put the firmware binaries in /lib/firmware.

tekram tm-802b card working in toshiba laptop using ndiswrapper and windows driver (net8180.inf). The linux r8180 driver did not work. The tekram card uses a realtek chipset.
puppy 215ce on this laptop.

The same setup works on my Itronix xc6260 laptop puppy109ce and 212.

after much swearing and praying i've finally manged to get wg111t wireless adapter to work in puppy 2.17. you have download the firmware from http://kbserver.netgear.com/release_notes/d102626.asp then you have to find the .inf file (can't remember which one though ) but i know it does work.


windows did not become a shoddy product overnight it took years of practice

This USB NIC is so low-budget, there is no brand name ANYWHERE on it, the package, or in the documentation.......

USBview showed as ZyDAS USB 2 device.

Used Zyxel zd1211rw driver supplied kindly by puppy, and hey-presto, a working wireless. Gol-DANG!!!!!

Ken
PS cost me $10 new still in wrapper

netgear wg111v2 USB works in puppy linux.

See this thread for more information: http://www.murga-linux.com/puppy/viewto ... 442#121442

I've used it in Puppy 2.14 and 2.16 so far.

Also, I suggest the original thread creator reorganize the devices into alphabetical order. A quick run with a spreadsheet program ought to sort things out.

D-Link DWL-122G rev B1 USB adapter works in 2.17.1.

This uses the Ralink RT2570 chipset & the driver in earlier Puppys would never load on my VIA EPIA 5000. Now it does.

But, the network connection wizard in 2.17.1 doesn't configure it properly. Instead, use the rutilt utility which does work.

I haven't yet figured out how to save the configuration from rutilt so it connect automatically on next boot.

Netcomm Wireless USB dongle NP544 works with NOP-217-up1, using ndiswrapper

Also works with Puppy-pro, also with ndiswrapper.

Doesn't seem to work with other puppies I have tried, such as simplepup and chinesepuppy 2.13

livedisk running over win2k

Netopia 3d reach runs fine w/ acx drivers

CNET CWD-854 wireless USB2 netcard works fine in puppy 2.16 with rausb0 (rt73).

I have posted elsewhere on the puppy forums that with 2.17.1, my integrated wireless works without any action save for configuring wireless network.

I cannot guarantee that Puppy isn't using ndiswrapper (I haven't checked to see if it is loaded) but it isn't asking me for a path to the windows driver or inf file.

The important thing is that it is working with miminal irritation (solely that it doesn't remember the wireless profile and I have to launch the Network Wizard and select "use that profile" several times each time I boot).

Steve

i thought i had already listed this, but...

netgear wg511u (athros chipset) works in puppies 2.10 through 2.13 both with native linux driver, and ndiswrapper (it's a bit easier to run with ndiswrapper).

i can also confirm it working in 2.13 for wpa-psk with ether driver using the network wizard version 2.14-8.

reedit: edit: the device works using both rutilt and the connection wizard for open APs, but needs the wizard for wpa-psk. also, i have not had a chance to test it with wep.

too bad my pcmcia slot went south, i'm now forced to work on getting a usb adapter working (see my post in bugs). it's one that someone posted as working, so i'm guessing i should read that thread.