The time now is Mon 20 May 2013, 05:05
All times are UTC - 4 |
| Author |
Message |
Lauri
Guest
|
 Posted: Mon 15 Aug 2005, 03:21 Post subject:
 Network configuration problem (Puppy-1.0.4 with XFree 4.5.0) |
|
PCMCIA-Card (XIRCOM Credit Card Ethernet 10/100) is correctly detected (checked with "cardctl ident") and the appropriate driver is loaded ("lsmod").
When using the networkwizard, there's only the option, to add a driver or EXIT, the buttons to test or configure the network are missing.
Any idea, how to go further ? (Hardware is ok, works with other distributions and Win...)
|
|
Back to top
|
|
 |
Guest
Guest
|
| Posted: Mon 15 Aug 2005, 03:49 Post subject:
|
|
Wizzard is a no go in that area...
edit by hand, it's not that hard
/etc/pcmcia/network.opts
Then when the pcmcia subsytem loads the driver it will bring up the network..
easy hey
|
|
Back to top
|
|
|
lauri
Guest
|
| Posted: Mon 15 Aug 2005, 16:18 Post subject:
|
|
maybe easy for you !  not for me at this moment 
can you give me some details, what to fill in; I would like to use dhcp.
|
|
Back to top
|
|
|
Guest
Guest
|
| Posted: Mon 15 Aug 2005, 18:26 Post subject:
|
|
mmmmm If you had of looked at the file....
but here you go
| Code: |
# Network adapter configuration
#
# The address format is "scheme,socket,instance,hwaddr".
#
# Note: the "network address" here is NOT the same as the IP address.
# See the Networking HOWTO. In short, the network address is the IP
# address masked by the netmask.
#
case "$ADDRESS" in
*,*,*,*)
INFO="Sample private network setup"
# Use this to override the interface name -- see 'man nameif'
NAMEIF=""
# Transceiver selection, for some cards -- see 'man ifport'
IF_PORT=""
# Use BOOTP (via /sbin/bootpc, or /sbin/pump)? [y/n]
BOOTP="n"
# Use DHCP (via /sbin/dhcpcd, /sbin/dhclient, or /sbin/pump)? [y/n]
DHCP="n"
# If you need to explicitly specify a hostname for DHCP requests
DHCP_HOSTNAME=""
# Host's IP address, netmask, network address, broadcast address
IPADDR=""
NETMASK="255.255.255.0"
NETWORK="10.0.1.0"
BROADCAST="10.0.1.255"
# Gateway address for static routing
GATEWAY="10.0.1.1"
# Things to add to /etc/resolv.conf for this interface
DOMAIN=""
SEARCH=""
DNS_1=""
DNS_2=""
DNS_3=""
# NFS mounts, should be listed in /etc/fstab
MOUNTS=""
# If you need to override the interface's MTU...
MTU=""
# For IPX interfaces, the frame type and network number
IPX_FRAME=""
IPX_NETNUM=""
# Extra stuff to do after setting up the interface
start_fn () { return; }
# Extra stuff to do before shutting down the interface
stop_fn () { return; }
# Card eject policy options
NO_CHECK=n
NO_FUSER=n
;;
esac
|
change this line to as follows
| Code: |
# Use DHCP (via /sbin/dhcpcd, /sbin/dhclient, or /sbin/pump)? [y/n]
DHCP="y"
|
And that's all you need to do
|
|
Back to top
|
|
|
lauri
Guest
|
| Posted: Tue 16 Aug 2005, 02:14 Post subject:
|
|
That's what I've already done, before I asked the question. But this seems to have no effect; after rebooting there was no device eth0 (checking with ifconfig eth0). I'll try it once again, maybe put some "debug"-info into network.opts, to see, if this file is used by another at all.
|
|
Back to top
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
Forum index » House Training » Beginners Help ( Start Here)
