slacko64 & slacko(32)6.3.0.6
Additional findings:
On the laptop that I provide a report on, earlier, closing the laptop lid causes it to go to sleep. But, upon reopening, the system cannot get back to desktop requiring a Hard stop and restart of the laptop.
Again, this is an non-UEFI HP laptop with X2 processor which is used in testing.
Hope this is helpful
On the laptop that I provide a report on, earlier, closing the laptop lid causes it to go to sleep. But, upon reopening, the system cannot get back to desktop requiring a Hard stop and restart of the laptop.
Again, this is an non-UEFI HP laptop with X2 processor which is used in testing.
Hope this is helpful
Slacko64 6.3.0.6 live cd on an even older non-UEFI box.
Booting and working ootb.
Booting and working ootb.
Code: Select all
# inxi -Fxx
System: Host: puppypc30864 Kernel: 4.1.11 x86_64 (64 bit, gcc: 4.8.2)
Desktop: JWM 2.3.2 dm: N/A Distro: Slacko64 Puppy 6.3.0.6
Machine: Mobo: ASUSTeK model: A8V-MQ version: Rev 1.xx serial: MB-1234567890
Bios: American Megatrends version: 0210 date: 03/31/2006
CPU: Single core AMD Athlon 64 3800+ (-UP-) cache: 512 KB flags: (lm nx sse sse2 sse3) bmips: 4801.98 clocked at 2399.992 MHz
Graphics: Card: NVIDIA NV18 [GeForce4 MX 4000] bus-ID: 05:00.0 chip-ID: 10de:0185
X.org: 1.14.3 drivers: nouveau (unloaded: fbdev,vesa) tty size: 80x25 Advanced Data: N/A for root
Audio: Card: VIA VT8233/A/8235/8237 AC97 Audio Controller
driver: snd_via82xx port: e400 bus-ID: 00:11.5 chip-ID: 1106:3059
Sound: Advanced Linux Sound Architecture ver: k4.1.11
Network: Card: VIA VT6102 [Rhine-II] driver: via-rhine port: e800 bus-ID: 00:12.0 chip-ID: 1106:3065
IF: eth0 state: unknown speed: 100 Mbps duplex: full mac: 00:15:f2:3d:a8:d4
Drives: HDD Total Size: 250.1GB (-)
1: id: /dev/sda model: WDC_WD2500AAKX size: 250.1GB serial: N/A
Partition: ID: swap-1 size: 4.19GB used: 0.00GB (0%) fs: swap
RAID: System: supported: linear raid0 raid1 raid10 raid6 raid5 raid4
No RAID devices detected - /proc/mdstat and md_mod kernel raid module present
Unused Devices: none
Sensors: None detected - is lm-sensors installed and configured?
Info: Processes: 94 Uptime: 9 min Memory: 245.4/1998.7MB Runlevel: 5 Gcc sys: 4.8.2
Client: Shell (bash 4.2.53 running in urxvt) inxi: 1.9.17
Code: Select all
# free
total used free shared buffers
Mem: 2046708 774960 1271748 263764 79140
-/+ buffers: 695820 1350888
Swap: 4095996 0 4095996
-
- Posts: 902
- Joined: Mon 22 Jun 2009, 01:36
- Location: Philadelphia, PA
laptop lid
I don't know if it'll be of any help, but I'll try it on my laptop, and report.gcmartin (in part) wrote:On the laptop that I provide a report on, earlier, closing the laptop lid causes it to go to sleep. But, upon reopening, the system cannot get back to desktop requiring a Hard stop and restart of the laptop.
Again, this is an non-UEFI HP laptop with X2 processor which is used in testing.
EDIT: OK, downloaded the 6.3.0.6 32bit iso, extracted to a hard drive directory. Files as at bottom of this post.
Booted frugal slacko, looked fine.
Closed the lid, and the blue power light goes off and on (this is the Dell E6410, I5 Intel processor, presumably uses BIOS rather than UEFI?)
Opened the lid, the screen was blank, then the desktop came back.
Is this called suspend?
Thanks,
Sheldon
-rw-r--r-- 1 root root 4194304 Apr 5 00:50 efi.img
-rwxr-xr-x 1 root root 3751 Apr 4 23:07 fix-usb.sh
-rw-r--r-- 1 root root 551 Apr 5 00:50 grub.cfg
-rw-r--r-- 1 root root 1331143 Apr 5 00:38 initrd.gz
-rw-r--r-- 1 root root 180445216 Apr 5 00:49 puppy_slacko_6.3.0.6.sfs
-rw-r--r-- 1 root root 153872 Mar 11 2013 vesamenu.c32
-rw-r--r-- 1 root root 4688240 Apr 5 00:38 vmlinuz
-rw-r--r-- 1 root root 30801952 Apr 5 00:38 zdrv_slacko_6.3.0.6.sfs
Dell E6410: BusterPup, BionicPup64, Xenial, etc
Intel DQ35JOE, Dell Vostro 430
Dell Inspiron, Acer Aspire One, EeePC 1018P
Intel DQ35JOE, Dell Vostro 430
Dell Inspiron, Acer Aspire One, EeePC 1018P
Hi gcmartin,gcmartin wrote:Additional findings:
On the laptop that I provide a report on, earlier, closing the laptop lid causes it to go to sleep. But, upon reopening, the system cannot get back to desktop requiring a Hard stop and restart of the laptop.
Again, this is an non-UEFI HP laptop with X2 processor which is used in testing.
Hope this is helpful
Can you try one thing for me on that laptop? Can be running Slacko 6.3.0, 6.3.0.6, or any of their recent derivs. Change the following in /etc/acpi/actions/suspend.sh (save the orig. first):
comment out lines 33 and 40.
add a " and a LF to line 43
Save it and try the lid suspend. I really don't expect that to do it but I don't have a machine that fails lid suspend to try it on.
Thanks,
Pups currently in kennel :D Older LxPupSc and X-slacko-4.4 for my users; LxPupSc, LxPupSc64 and upupEF for me. All good pups indeed, and all running savefiles for look'n'feel only. Browsers, etc. solely from SFS.
I have a bunch of machines, mostly older laptops and desktop
I've booted the HP DV9917CL and the Dell D620 with 6.3.0.6 so far, no troubles. If I could get my software ported to it and get to where I could easily load my tweaked version, I'd like to do that.
I've customized the Slacko 5.7.0 quite a bit (different kernel, grub2, conky, but mostly just added programs and games, some not normally available), and am trying to figure out how can I do an install of 6.3.0.6 to a machine, add my mods, and then create from that a new ISO that I can burn to CD for the machine that is so old it only has USB 1.1 so can't boot from a flashdrive, and be able to use that CD to install to any of my machines? On my 5.7.0 I have isomaster and pburn, but can't get either to do it, but maybe I'm doing something wrong. Can anyone point me to a how to for tweaking and making a new ISO out of it?
Thanks for creating Slacko, 5.7.0 Mick. I've got almost everything I wanted, and my only problems are because people keep messing with flash stuff, making it incompatible with the code I'm running. My guess is 6.3.0.6 has better odds of those things working too.
I've customized the Slacko 5.7.0 quite a bit (different kernel, grub2, conky, but mostly just added programs and games, some not normally available), and am trying to figure out how can I do an install of 6.3.0.6 to a machine, add my mods, and then create from that a new ISO that I can burn to CD for the machine that is so old it only has USB 1.1 so can't boot from a flashdrive, and be able to use that CD to install to any of my machines? On my 5.7.0 I have isomaster and pburn, but can't get either to do it, but maybe I'm doing something wrong. Can anyone point me to a how to for tweaking and making a new ISO out of it?
Thanks for creating Slacko, 5.7.0 Mick. I've got almost everything I wanted, and my only problems are because people keep messing with flash stuff, making it incompatible with the code I'm running. My guess is 6.3.0.6 has better odds of those things working too.
Ok, I tested it on an AMD X2 laptop
It ran fine, suspended on close and resumed fine.
Hp pavilion dv9917cl
amd turion x2
Hp pavilion dv9917cl
amd turion x2
- Attachments
-
- inxipic.jpg_2016-04-18_233300.png
- (87.2 KiB) Downloaded 361 times
@Marv, Thanks!
Without making ANY changes, I booted 6301 on LiveCDRW.
Using 6301, I don't have the earlier problems reported when booted 6306; namely lid reopening as well as wired LAN works w/6301.
I cannot find my 6306 disc ATM. When I do, I'll test again. Should I have the problems, again, I will apply your fix, and report what happens on this thread.
Edit: 6306 DVD+RW was overwritten. Will wait for next release.
Without making ANY changes, I booted 6301 on LiveCDRW.
Using 6301, I don't have the earlier problems reported when booted 6306; namely lid reopening as well as wired LAN works w/6301.
I cannot find my 6306 disc ATM. When I do, I'll test again. Should I have the problems, again, I will apply your fix, and report what happens on this thread.
Edit: 6306 DVD+RW was overwritten. Will wait for next release.
-
- Posts: 21
- Joined: Tue 04 Dec 2012, 05:24
Booting from CD, Slacko64 6.3.0.6 behaves even worse than Slacko64 6.3.0.0 on my newish HP laptop.
Neither can find my audio, wired network, or wireless network card, nor graphics drivers for the onboard Intel and Nvidia chips.
6.3.0, told to boot to an intermediate resolution, boots to the highest res.
6.3.0.6 doesn't even get that far; no x, lockups, kernel panics, all sorts of entertainment.
In both cases, the file "fdrv_slacko_6.0.8.1.sfs" is not present on the CD.
How do I get the driver file?
Neither can find my audio, wired network, or wireless network card, nor graphics drivers for the onboard Intel and Nvidia chips.
6.3.0, told to boot to an intermediate resolution, boots to the highest res.
6.3.0.6 doesn't even get that far; no x, lockups, kernel panics, all sorts of entertainment.
In both cases, the file "fdrv_slacko_6.0.8.1.sfs" is not present on the CD.
How do I get the driver file?
How Puppy works:
http://puppylinux.com/development/howpuppyworks.html
http://puppylinux.com/development/howpuppyworks.html
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
- LazY Puppy
- Posts: 1934
- Joined: Fri 21 Nov 2014, 18:14
- Location: Germany
Could anyone please explain this?
http://www.murga-linux.com/puppy/viewto ... 302#904302
http://www.murga-linux.com/puppy/viewto ... 398#904398
http://www.murga-linux.com/puppy/viewto ... 302#904302
http://www.murga-linux.com/puppy/viewto ... 398#904398
RSH
"you only wanted to work your Puppies in German", "you are a separatist in that you want Germany to secede from Europe" (musher0) :lol:
No, but I gave my old drum kit away for free to a music store collecting instruments for refugees! :wink:
"you only wanted to work your Puppies in German", "you are a separatist in that you want Germany to secede from Europe" (musher0) :lol:
No, but I gave my old drum kit away for free to a music store collecting instruments for refugees! :wink:
slacko64 & slacko(32)6.3.0.6
Manual frugal install to a usb-3.0 hard drive, pc is a HP desktop:
video-info-glx 1.5.3 Fri 20 May 2016 on Slacko64 Puppy 6.3.0.6 Linux 4.1.11 x86_64
2.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller (rev 09)
oem: Intel(R) Sandybridge/Ivybridge Graphics Chipset Accelerated VGA BIOS
product: Intel(R) Sandybridge/Ivybridge Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 3200x900 pixels (846x237 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Desktop
OpenGL core profile version string: 3.1 (Core Profile) Mesa 9.1.7
Intel(R) Core(TM) i5-3550 CPU @ 3.30GHz
Core 0: @1688 1: @1698 2: @1639 3: @1644 MHz
The bios is set to legacy.
It's working okay so far.
video-info-glx 1.5.3 Fri 20 May 2016 on Slacko64 Puppy 6.3.0.6 Linux 4.1.11 x86_64
2.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller (rev 09)
oem: Intel(R) Sandybridge/Ivybridge Graphics Chipset Accelerated VGA BIOS
product: Intel(R) Sandybridge/Ivybridge Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 3200x900 pixels (846x237 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Desktop
OpenGL core profile version string: 3.1 (Core Profile) Mesa 9.1.7
Intel(R) Core(TM) i5-3550 CPU @ 3.30GHz
Core 0: @1688 1: @1698 2: @1639 3: @1644 MHz
The bios is set to legacy.
It's working okay so far.
- Attachments
-
- Screenshot.jpg
- (30.96 KiB) Downloaded 989 times
- ttuuxxx
- Posts: 11171
- Joined: Sat 05 May 2007, 10:00
- Location: Ontario Canada,Sydney Australia
- Contact:
Hi I running Slacko 6.3.0 , LoL i'm a couple releases behind Anyways,Using Firefox, I was trying to watch some CTV news from Canada and it said to get the latest version of Adobe flash, well I had the latest version and that wasn't good enough, So I looked into pepflash and compiled libfreshwrapper-flashplayer and tossed in libpepflashplayer.so from Chrome, So now newer play media works, Youtube works, So far so good, Oh ya I had to configure it a bit and compile libvdpau and made a pet package, once you install it you have to restart FireFox to get it to work, Oh and probably delete flashplayer first before installing it.
The nice thing is that its only a 4.6MB pet
Anyways have fun with it.
ttuuxxx
http://smokey01.com/ttuuxxx/Slacko/libp ... .1.2.3.pet
The nice thing is that its only a 4.6MB pet
Anyways have fun with it.
ttuuxxx
http://smokey01.com/ttuuxxx/Slacko/libp ... .1.2.3.pet
http://audio.online-convert.com/ <-- excellent site
http://samples.mplayerhq.hu/A-codecs/ <-- Codec Test Files
http://html5games.com/ <-- excellent HTML5 games :)
http://samples.mplayerhq.hu/A-codecs/ <-- Codec Test Files
http://html5games.com/ <-- excellent HTML5 games :)
Manual frugal install to a usb-3.0 hard drive, pc is a macmini.
video-info-glx 1.5.3 Thu 16 Jun 2016 on Slacko Puppy 6.3.0.6 Linux 3.14.55 i686
2.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
oem: Intel(R) Sandybridge/Ivybridge Graphics Chipset Accelerated VGA BIOS
product: Intel(R) Sandybridge/Ivybridge Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 1920x1080 pixels (507x285 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Mobile x86/MMX/SSE2
OpenGL core profile version string: 3.1 (Core Profile) Mesa 9.1.7
Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz
Core 0: @1200 1: @1200 2: @1200 3: @1200 MHz
It's working well.
video-info-glx 1.5.3 Thu 16 Jun 2016 on Slacko Puppy 6.3.0.6 Linux 3.14.55 i686
2.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
oem: Intel(R) Sandybridge/Ivybridge Graphics Chipset Accelerated VGA BIOS
product: Intel(R) Sandybridge/Ivybridge Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 1920x1080 pixels (507x285 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Mobile x86/MMX/SSE2
OpenGL core profile version string: 3.1 (Core Profile) Mesa 9.1.7
Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz
Core 0: @1200 1: @1200 2: @1200 3: @1200 MHz
It's working well.
- Attachments
-
- Screenshot.jpg
- (100.09 KiB) Downloaded 768 times
Slacko 32bit 6.3.0.6 UEFI
Machine: Dell D620 512 meg of ram
Running well. Wireless connected straight away. Used 6.3.0 on the same machine and it was a lot slower and less stable.
Trackpad working normally, (normally have to tweak it in older versions as it is sluggish) as are sound and video, Thanks MIcko a new toy.
Machine: Dell D620 512 meg of ram
Running well. Wireless connected straight away. Used 6.3.0 on the same machine and it was a lot slower and less stable.
Trackpad working normally, (normally have to tweak it in older versions as it is sluggish) as are sound and video, Thanks MIcko a new toy.
Last edited by Robert123 on Sat 18 Jun 2016, 19:02, edited 2 times in total.
slacko64 & slacko(32)6.3.0.6
I did a manual frugal install to a usb-3.0 flash drive, pc is a lenovo
desktop.
video-info-glx 1.5.3 Fri 17 Jun 2016 on Slacko Puppy 6.3.0.6 Linux 3.14.55 i686
0.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 430] (rev a1)
oem: NVIDIA
product: GF108 Board - 1071v1p1 Chip Rev
X Server: Xorg Driver: nvidia
X.Org version: 1.14.3
dimensions: 1920x1080 pixels (524x292 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.4
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce GT 430/PCIe/SSE2
OpenGL core profile version string: 4.3.0 NVIDIA 361.45.11
Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
Core 0: @2003 1: @2003 MHz
It's working well on this one too.
desktop.
video-info-glx 1.5.3 Fri 17 Jun 2016 on Slacko Puppy 6.3.0.6 Linux 3.14.55 i686
0.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 430] (rev a1)
oem: NVIDIA
product: GF108 Board - 1071v1p1 Chip Rev
X Server: Xorg Driver: nvidia
X.Org version: 1.14.3
dimensions: 1920x1080 pixels (524x292 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.4
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce GT 430/PCIe/SSE2
OpenGL core profile version string: 4.3.0 NVIDIA 361.45.11
Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
Core 0: @2003 1: @2003 MHz
It's working well on this one too.
- Attachments
-
- Screenshot.jpg
- (67.19 KiB) Downloaded 663 times
slacko64 & slacko(32)6.3.0.6
Manual frugal install to a usb-3.0 hard drive, pc is a macmini.
video-info-glx 1.5.3 Sun 19 Jun 2016 on Slacko64 Puppy 6.3.0.6 Linux 4.1.11 x86_64
2.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
oem: Intel(R) Sandybridge/Ivybridge Graphics Chipset Accelerated VGA BIOS
product: Intel(R) Sandybridge/Ivybridge Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 1920x1080 pixels (508x285 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Mobile
OpenGL core profile version string: 3.1 (Core Profile) Mesa 9.1.7
Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz
Core 0: @1800 1: @2501 2: @1900 3: @1800 MHz
I'm using the devx_slacko64_6.3.0.sfs which I downloaded from ibiblio.org
I added apps with PPM + a few others.
It's working well so far.
Thanks
Here's a small pet of gtktetris, it'll create an icon in the Fun section of the Puppy menu, not the proper icon but it works just the same.
video-info-glx 1.5.3 Sun 19 Jun 2016 on Slacko64 Puppy 6.3.0.6 Linux 4.1.11 x86_64
2.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
oem: Intel(R) Sandybridge/Ivybridge Graphics Chipset Accelerated VGA BIOS
product: Intel(R) Sandybridge/Ivybridge Graphics Controller Hardware Version 0.0
X Server: Xorg Driver: intel
X.Org version: 1.14.3
dimensions: 1920x1080 pixels (508x285 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: SGI
server glx version string: 1.4
OpenGL vendor string: Intel Open Source Technology Center
OpenGL renderer string: Mesa DRI Intel(R) Ivybridge Mobile
OpenGL core profile version string: 3.1 (Core Profile) Mesa 9.1.7
Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz
Core 0: @1800 1: @2501 2: @1900 3: @1800 MHz
I'm using the devx_slacko64_6.3.0.sfs which I downloaded from ibiblio.org
I added apps with PPM + a few others.
It's working well so far.
Thanks
Here's a small pet of gtktetris, it'll create an icon in the Fun section of the Puppy menu, not the proper icon but it works just the same.
- Attachments
-
- gtktetris.jpg
- (38.56 KiB) Downloaded 546 times
-
- gtktetris-0.6.2-x86_64.pet
- (13.68 KiB) Downloaded 198 times
-
- Screenshot.jpg
- (33.04 KiB) Downloaded 573 times
The xorg-server version in slackware 14.1 is 1.14.3... the last updates are in 1.14.7. this has to be fixed, there is a slackbuild for xorg-server, i guess 1.14.7 can be compiled with it.
In august 2014 there were people already asking for an update. i find it quite sad that after two years the situation is the same. The fix i'm looking for is probably in 1.14.7
http://www.linuxquestions.org/questions ... 175513059/
This is the slackbuild:
http://ftp.slackware.com/pub/slackware/ ... rg-server/
This is xorg-server 1.14.7
https://www.x.org/releases/individual/x ... .7.tar.bz2
that file should go to src/sources in the slackbuild (i guess), remove the previous version first.
In august 2014 there were people already asking for an update. i find it quite sad that after two years the situation is the same. The fix i'm looking for is probably in 1.14.7
http://www.linuxquestions.org/questions ... 175513059/
This is the slackbuild:
http://ftp.slackware.com/pub/slackware/ ... rg-server/
This is xorg-server 1.14.7
https://www.x.org/releases/individual/x ... .7.tar.bz2
that file should go to src/sources in the slackbuild (i guess), remove the previous version first.