Puppy Linux Discussion Forum

[FeodorF]

[rcrsn51]

[gcmartin]

Anyone else having issues with Slacko awakening after sleep on Laptops? If so, describe.

[simargl]

.

[bark_bark_bark]

[FeodorF]

[James C]

Another fresh manual frugal install...looking good.

# report-video
VIDEO REPORT: Slacko Puppy, version 5.6

Chip description:
VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02)

Requested by /etc/X11/xorg.conf:
Resolution (widthxheight, in pixels): 1024x768
Depth (bits, or planes): 24
Modules requested to be loaded: dbe

Probing Xorg startup log file (/var/log/Xorg.0.log):
Driver loaded (and currently in use): intel
Loaded modules: dbe dri dri2 extmod fb glx kbd mouse record

Actual rendering on monitor:
Resolution: 1024x768 pixels (270x203 millimeters)
Depth: 24 planes

...the above also recorded in /tmp/report-video
# glxgears
Running synchronized to the vertical refresh. The framerate should be
approximately the same as the monitor refresh rate.
378 frames in 5.0 seconds = 75.520 FPS
376 frames in 5.0 seconds = 75.143 FPS
376 frames in 5.0 seconds = 75.143 FPS
376 frames in 5.0 seconds = 75.143 FPS
376 frames in 5.0 seconds = 75.143 FPS

-Computer-
Processor : Intel(R) Pentium(R) 4 CPU 2.80GHz
Memory : 2592MB (158MB used)
Machine Type : Physical machine
Operating System : Slacko Puppy - 5.6
User Name : root (root)
Date/Time : Fri 16 Aug 2013 12:27:01 AM CDT
-Display-
Resolution : 1024x768 pixels
OpenGL Renderer : Mesa DRI Intel(R) 865G x86/MMX/SSE2
X11 Vendor : The X.Org Foundation
-Audio Devices-
Audio Adapter : ICH4 - Intel ICH5

[FeodorF]

Operating System: Slacko Puppy 5.6
Kernel Version: Linux 3.4.52 (i686)
Date/Time: Fri 16 Aug 2013 07:42:21 PM GMT-1

Processor: AMD Athlon XP 3000
RAM: 968MB (219MB used)
Motherboard: ASRock K7S41GX, AMI BIOS P2.80 10/18/2006

VGA controller: SiS 661/741/760, 128MB
Graphics: 1440x900x24
Driver: SiS, Galium 0.4 on softpipe, 2.1 Mesa 8.0.4

Audio: ICH-SiS SI7012

eth0: SiS 900 PCI Fast Ethernet driver
wlan0: rtl871x wireless lan driver

RAID bus controller: VIA Technologies, Inc. VT6421 IDE RAID Controller (rev 50)
Storage: ATA ExcelStor Techno
Drive: HL-DT-ST DVD-RAM GH22NP20

USB: Generic Storage Device
----------------------------------------------------------
'Frugal' install on hard disk works fine!

[FeodorF]

I had to give it a try.

Slacko 5.6 PAE (K-3.10.5 i686 [X.org:1.12.4]) Live-CD boots up within 300 seconds into a 1600x900x24 / 1280x800x24 screen.

I have tested an old ATI (Rage IIC AGP) and a MGA (Mystique PCI) graphic card - both capable of 1280x800x24.

Also tested an old ATI (Rage IIC Ver.7a AGP) - capable of 1600x900x24, To get into the technical detail of this card I included the /var/log/X.org.0.log file.

Add up: Trio64V2 graphic card (using the S3-driver) tested with 800x600x24 - just to proof functionality with X.org:1.12.4 - nothing else.

Posting of it right now - Pentium-II 266MHz.

[FeodorF]

Just tested my Pentium-III 933MHz equipped with a 'quirk' nvidia GeForce4-MX440 card from China.

Needs the 'nv' driver in order to render applications in 'full scale' mode.

Good to know that I can use PAE Kernel-3.10.5 and X.Org 1.12.4 for this box.

[bigpup]

Live CD with save file on hard drive.
Netgear n300 USB wireless network adapter.

When I boot up, my network adapter is not working or even turned on.
I can use Network Wizard to set it up, using Ndiswrapper, and a Windows driver. It is activated and works now.
I save this setup, but on reboot, adapter is not working or even turned on.
Rerun Network Wizard, setup, and connection works. The profile is saved, but I have to select it and run setup at each boot.

So, I tried using Frisbee.
Setup connection.
Rebooted.
Network adapter active and connection working.
With Frisbee, the settings were saved and used at next bootup.
At bootup, there are Frisbee messages about eth0 and wlan0 shutdown. It then activates wlan0 and connection working.

I have tried to find this, but I seem to remember Barry stating (in his blog) something about having Wlan turned off when he was making changes to the startup scripts.

[Billtoo]

I did a manual frugal install of my remastered slacko 5.6.0 pae iso to a 32gb
Micro SDHC card.
On first boot there were no network modules available when I ran
frisbee, I realized that I hadn't copied zdrv_slacko_5.6.0.sfs into
the directory along with the other 3 files...damn...so I fixed the
mistake and it's working.
video-info-glx 1.5.3 Sat 17 Aug 2013 on Slacko Puppy 5.6.0 Linux 3.10.5 i686
0.0 VGA compatible controller:nVidia Corporation GF108[GeForceGT430](rev a1)
oem: NVIDIA
product: GF108 Board - 1071v0p1 Chip Rev
X Server: Xorg Driver: nvidia
X.Org version: 1.12.4
dimensions: 1920x1080 pixels (513x292 millimeters)
depth of root window: 24 planes
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.4
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce GT 430/PCIe/SSE2/3DNOW!
OpenGL version string: 4.3.0 NVIDIA 325.15
# glxgears
Running synchronized to the vertical refresh. The framerate should be
approximately the same as the monitor refresh rate.
302 frames in 5.0 seconds = 60.387 FPS
300 frames in 5.0 seconds = 60.000 FPS
301 frames in 5.0 seconds = 60.002 FPS
#
AMD Phenom(tm) II X6 1045T Processor
Core 0: @800 1: @800 2: @800 3: @800 4: @800 5: @800 MHz
Memory 8309MB (167MB used)
Network controller Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe

It's working well.

EDIT:I installed an old hearts game for windows in wine that would run
in the windows dos shell but it calls up dosbox in Slacko which is
pretty amazing I think

[watchdog]

[koulaxizis]

I just install Slacko 5.6 on a netbook Acer Aspire One (mine) and on a custom-made desktop computer with most recent hardware (not mine). Well, i don't know how to say it... It's freaking AWESOME!! Thank you 01micko for another quality release!!

[Sage]

Slacko Puppy is now shutting down .....
but doesn't after new (wiped) FULL on first restart only.
Something missing?
Hard reset causes predictable messages and file chk - reboot then OK, except, Xorg 'Ignore'.
Also getting (first FULL run) "cannot (something?) in tmp/???
but it does start!
Fairly trivial but might confuse some punters? Still better than sliced bread...