Puppy Linux Discussion Forum

rerwin · Joined: 24 Aug 2005 Posts: 1553 Location: Maine, USA

Attached is what I hope to be my final implementation for the various Broadcom 43xx wifi cards. It is much simpler than the previous experiments and replaces all of the experiment packages on the previous page (24). The main difference is that, instead of having all open-source drivers wait for the proprietary driver to run, now the proprietary driver waits for the open-source drivers to do whatever they do and then reloads them as necessary.

This "experiment-7" omits the logic to switch between versions of the proprietary wl driver (5.100 vs. 5.60), because peebee's multi-kernel driver packages support only one of them (whichever the user chooses to install). It simplifies the selection between proprietary and open-source drivers for the case where wl produces an error message, by utilizing an earlier message that identifies the problematic devices, thus avoiding the need to wait for wl to run to see the error message.

I have separated the two parts of the previous experiments to create a "universal" part intended for all puppies (including lucid pup) and a package containing the brcm drivers for precise puppy 5.3.3.3. The "universal" package can be installed after installing peebee's broadcom_sta_v5.100.82.112_patched_x86_32-multi.pet package (or the 5.60 equivalent) for testing. Once "experiment-7" is verified by those of you with the Broadcom wifi devices, I hope that peebee will adopt this version for his packages. My goal is to repackage this experiment as a submission for incorporation into woof, for all new puppies (unless it makes more sense to keep it with the proprietary-driver packages).

To have this package install correctly, be sure to add it to an existing pupsave environment. This is because it includes file removals, which are not preserved in the initial creation of a pupsave file. (Lupuplus ISOs contain a fix for this, but it has not yet been accepted for newer woof-based puppies.) For precise pup 5.2.60, a "small fixes" package containing the fix is here:
http://www.murga-linux.com/puppy/viewtopic.php?p=633525#633525
Richard

rerwin · Joined: 24 Aug 2005 Posts: 1553 Location: Maine, USA

I have now corrected the bug I found and have re-uploaded the experiment package. Testing with the previous upload should still be valid except that b43 would be loaded along with wl. Peebee told me some time ago that the presence of b43 does not impact his test results. But the advice is to avoid having them both run, to avoid possible interference, so that's my design. Likewise for wl and brcmsmac.

Sorry for inconveniencing the 3 of you who downloaded the original.
Richard

peebee

wsamh · Joined: 16 Apr 2010 Posts: 79

I have two problems when I install vlc and playonlinux. When I run vlc on the terminal, It says that I cannot run vlc as root. Also when I run playonlinux, It says that I need to install python. I already did and It still says that. I install python version 2.7.2. Does anyone know how I can fix these two?

oldyeller · Joined: 15 Nov 2011 Posts: 826 Location: Mishawaka IN

Hello everyone,

I have done woof2 build of Precise 5.2.60 here.

I don't think it is close to what pemasu has done, but I took on the challenge to continue this Puppy

Cheers

gcmartin · Joined: 14 Oct 2005 Posts: 4620 Location: Earth

Precise History - Puppy version
There was Barry's 1st version, then this, then Barry's 2nd version, then other(s).

Quesitons

Is this PUP still in active development?
Will this Precise distro, and kernel upgrades continue?

Thanks in advance

oldyeller · Joined: 15 Nov 2011 Posts: 826 Location: Mishawaka IN

Pelo · Last edited by Pelo on Tue 23 Apr 2013, 07:20; edited 1 time in total

save only to USB : strange ! whatever i write at shutdown for first save , I only can save to my usb, not else where.
Your distro works fine on other hand. Merci pour votre travail. Pelo

bruno · Joined: 08 Mar 2012 Posts: 73 Location: Belgium

When i startup Upup 5333, then it makes connection by DHCP immediately, showing an IP, and then resets it immediately, and then gives message "internet connection failed".
All I have to do then is reset it manually with frisbee, but why it always disconnects?
Maybe i have to change something with the settings?
The other puppy's that I run on this machine don't have that problem.

Pelo

font color : broken ?
No colors at all, apparently. Big bug !

Pelo

How can we change a task to make it a sub-task of another one ?
I want to put task 3 as a sub-task of task one.

Planner will be very useful when controled. Nice idea to include a planner in a distro.