Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Sat 20 Sep 2014, 04:03
All times are UTC - 4
 Forum index » Advanced Topics » Hardware » Networking » Ethernet
How to use Intel 82652EZ NIC in Quirky 1.4?
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 2 [25 Posts]   Goto page: 1, 2 Next
Author Message
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 15:39    Post subject:  How to use Intel 82652EZ NIC in Quirky 1.4?  

PC: i686 (Old Dell Desktop)
Distro: Puppy Quirky 1.4 (Older distro but it works for me and I am happy with it.)
Kernel: 2.6.31.14
NIC: Intel 82652EZ

I got the PET drivers for this long time ago. Don't remember the exact location of the driver.
Back to top
View user's profile Send private message 
rcrsn51


Joined: 05 Sep 2006
Posts: 9114
Location: Stratford, Ontario

PostPosted: Fri 01 Feb 2013, 15:45    Post subject:  

Run this command: lspci -nn

Is your NIC detected?

Then run: lspci -k

Is a kernel module being loaded for it?
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 16:09    Post subject:  

# lispci -nn
bash: lispci: command not found
# lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation 82865G Integrated Graphics Controller [8086:2572] (rev 02)
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02)
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller [8086:24db] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02)
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
01:08.0 Ethernet controller [0200]: Intel Corporation 82562EZ 10/100 Ethernet Controller [8086:1050] (rev 02)
#
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 16:10    Post subject:  

# lspci -k
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02)
Subsystem: Dell Device 01d5
00:06.0 System peripheral: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
Kernel modules: shpchp
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
01:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet Controller (rev 02)
Subsystem: Dell Device 01d5
Kernel driver in use: e100
Kernel modules: e100
#
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 16:12    Post subject:  

Presently, I am running the same OS from CD and it works ok. This was setup several years ago. I got above info. from running the live CD os.

Now, I wish to install the same on a USB drive. eth0 drivers needed for this.
Back to top
View user's profile Send private message 
rcrsn51


Joined: 05 Sep 2006
Posts: 9114
Location: Stratford, Ontario

PostPosted: Fri 01 Feb 2013, 16:28    Post subject:  

Your NIC is using the e100 module which has been in the Linux kernel for a long time.

Are you sure that you needed an additional PET to get it working in Quirky 1.4?

Why not set up the USB drive and see what happens?
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 16:34    Post subject:  

The OS on USB doesn't detect the NIC. This is even when I go to internet setup. Also tried ifconfig, it doesn't give any info. for eth0
Puppy Hardware info. also doesn't list eth0 when this is being run from USB. This is under network, interfaces. However, it is ok when run from live CD. (The live cd uses a custom .sfs file that is on my hard drive. Tried to copy this file to USB, it doesn't use it.)

Same happened to me the first time I used this OS several years ago. Got drivers for this in form of .pet somewhere.
Back to top
View user's profile Send private message 
rcrsn51


Joined: 05 Sep 2006
Posts: 9114
Location: Stratford, Ontario

PostPosted: Fri 01 Feb 2013, 16:47    Post subject:  

I looked in Quirky 1.4 and the e100 module is there. I loaded it manually with
Code:
modprobe e100


So I don't know why your USB install would be a problem.
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 16:52    Post subject:  

Will try this and see what happens.
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 17:24    Post subject:  

rcrsn51 wrote:
I looked in Quirky 1.4 and the e100 module is there. I loaded it manually with
Code:
modprobe e100


So I don't know why your USB install would be a problem.


I tried #modprobe e100
on the USB install. It gave fatal error, module not found.
Back to top
View user's profile Send private message 
rcrsn51


Joined: 05 Sep 2006
Posts: 9114
Location: Stratford, Ontario

PostPosted: Fri 01 Feb 2013, 19:09    Post subject:  

I would copy the core Puppy files off the CD onto the USB drive again.
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 19:11    Post subject:  

rcrsn51 wrote:
I would copy the core Puppy files off the CD onto the USB drive again.


Tried this thrice already, has not helped.
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 19:15    Post subject:  

I had same issue installing on a netbook abour two years ago, had to install drivers for that also:
http://www.murga-linux.com/puppy/viewtopic.php?t=61970
Back to top
View user's profile Send private message 
rcrsn51


Joined: 05 Sep 2006
Posts: 9114
Location: Stratford, Ontario

PostPosted: Fri 01 Feb 2013, 20:01    Post subject:  

rvijay wrote:
I had same issue installing on a netbook abour two years ago, had to install drivers for that also:
http://www.murga-linux.com/puppy/viewtopic.php?t=61970


That's a different issue. In that situation, your Puppy version was missing a kernel module. Here, Quirky 1.4 definitely has the e100 module.

Type this command: uname -r
Back to top
View user's profile Send private message 
rvijay

Joined: 07 Mar 2011
Posts: 25

PostPosted: Fri 01 Feb 2013, 20:05    Post subject:  

rcrsn51 wrote:
rvijay wrote:
I had same issue installing on a netbook abour two years ago, had to install drivers for that also:
http://www.murga-linux.com/puppy/viewtopic.php?t=61970


That's a different issue. In that situation, your Puppy version was missing a kernel module. Here, Quirky 1.4 definitely has the e100 module.

Type this command: uname -r


# uname -r
2.6.31.14
#
Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 1 of 2 [25 Posts]   Goto page: 1, 2 Next
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » Advanced Topics » Hardware » Networking » Ethernet
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0762s ][ Queries: 12 (0.0061s) ][ GZIP on ]