Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Tue 28 Jul 2015, 01:59
All times are UTC - 4
 Forum index » Advanced Topics » Cutting edge
pcb Xorg driver for Intel Poulsbo, with Puppy Lucid
Moderators: Flash, Ian, JohnMurga
Post new topic   Reply to topic View previous topic :: View next topic
Page 1 of 1 [7 Posts]  
Author Message
tempestuous

Joined: 10 Jun 2005
Posts: 5387
Location: Australia

PostPosted: Wed 20 Apr 2011, 00:04    Post subject:  pcb Xorg driver for Intel Poulsbo, with Puppy Lucid  

UPDATE June 05 2015:

I packaged the experimental pcb Xorg driver for Puppy Lucid here -
http://www.murga-linux.com/puppy/viewtopic.php?p=515093#515093

But various attempts to use this driver have failed.
A better solution for Poulsbo devices under Puppy Lucid is the fbdev graphics driver, available here -
http://www.murga-linux.com/puppy/viewtopic.php?t=67166

Last edited by tempestuous on Fri 05 Jun 2015, 04:03; edited 3 times in total
Back to top
View user's profile Send private message 
tempestuous

Joined: 10 Jun 2005
Posts: 5387
Location: Australia

PostPosted: Wed 20 Apr 2011, 00:16    Post subject:  

So clearly this driver would be ideal for Puppeee!
I have just sent a message to Jemimah to see if she can compile the kernel module for the Puppeee kernel.

I have already prepared a pcb Xorg package for Fluppy013, but I'm not sure what the situation is in Fluppy/Puppeee with OpenGL 3D libraries, so I will wait for Jemimah's response.
Back to top
View user's profile Send private message 
tempestuous

Joined: 10 Jun 2005
Posts: 5387
Location: Australia

PostPosted: Wed 20 Apr 2011, 00:17    Post subject:  

INSTRUCTIONS
Install the dotpets for the Xorg driver and kernel module, compatible with your Puppy version
(at this point, dotpet packages are only available for Puppy 5.1/5.2)
Optionally, you can also install the DRI (3D) dotpet.

First ensure you're actually running Xorg, not Xvesa!
Now you need to modify your Xorg configuration file, /etc/X11/xorg.conf
First I suggest you make a copy of this file in case of total failure! Call the copy something like "xorg.conf-backup"
Now open /etc/X11/xorg.conf in Geany.
Find the line under Section "Device" that starts with "Driver ...". The driver listed is likely to be "vesa" since that's the generic Xorg driver.
Change it to "pcb". Now the line looks like this -
Code:
Driver      "pcb" #card0driver

You might also change the "Identifier" value from "Card0" to "GMA500" but I don't think it's essential.
Now you need to add the following "Option" lines in the same section -
Code:
   Option "ShadowFB" "true"
   Option "DownScale" "false"
   Option "ExaNoComposite" "false"
   Option "IgnoreACPI" "true"
   Option "LidTimer" "false"
   Option "MigrationHeuristic" "greedy"
   Option "NoAccel" "false"
   Option "NoFitting" "false"
   Option "NoPanel" "false"
   Option "SWcursor" "false"
   Option "Vsync" "false"


In Section "ServerFlags" add this line:
Code:
Option "AIGLX" "true"


Now add a completely new section (it doesn't matter where)
Code:
Section "Extensions"
   Option   "Composite" "Disable"
   Option   "RENDER" "Enable"
EndSection


Now you're ready to restart the Xorg server with the new pcb driver.
Press Ctrl<Alt>Backspace to exit X, and type "xwin" to restart.
Hopefully you will have a nice powerful Xorg running with your GMA500!
But if you crash back to the commandline, you can reinstate your old xorg.conf file like this -
Code:
mv /etc/X11/xorg.conf-backup xorg.conf

or run the xorgwizard command to recreate a config file from scratch.
Back to top
View user's profile Send private message 
darkcity


Joined: 23 May 2010
Posts: 2507
Location: near here

PostPosted: Wed 23 Jan 2013, 09:36    Post subject:  

Did anyone ever succeed you this?

Someone considering Puppy here (scroll down)
http://www.reddit.com/r/LinuxActionShow/comments/16yc9x/bodilicious_bodhi_review_las_s25e04/

_________________
helping Wiki for help | IF SendSpace link = "dead" THEN PM me ("up file to http://meownplanet.net/")
Back to top
View user's profile Send private message Visit poster's website 
pemasu


Joined: 08 Jul 2009
Posts: 5467
Location: Finland

PostPosted: Wed 23 Jan 2013, 10:34    Post subject:  

There is now Poulsbo support available for Slacko and Upup Precise 3.7.2
Upup Precise needs that you install xorg modesetting driver as pet and one kernel module disabling (poulsbo.ko)
There is better kernel module now available and already in the distro.
Back to top
View user's profile Send private message 
Q5sys


Joined: 11 Dec 2008
Posts: 1128

PostPosted: Wed 23 Jan 2013, 11:26    Post subject:  

darkcity wrote:
Did anyone ever succeed you this?

Someone considering Puppy here (scroll down)
http://www.reddit.com/r/LinuxActionShow/comments/16yc9x/bodilicious_bodhi_review_las_s25e04/


are you referencing my post?
i was providing feedback to the email section of the show where someone asked about multiscreen in linux.

i didnt see anything in that thread about someone 'considering' puppy.
my feedback was actually the 5th comment in the thread. the post by the member with the gma chipset didnt even exist when i posted... and my post wasnt in reference to anything intel based.

_________________



Back to top
View user's profile Send private message Visit poster's website 
darkcity


Joined: 23 May 2010
Posts: 2507
Location: near here

PostPosted: Wed 23 Jan 2013, 16:33    Post subject:  

Thanks for the replies Cool
_________________
helping Wiki for help | IF SendSpace link = "dead" THEN PM me ("up file to http://meownplanet.net/")
Back to top
View user's profile Send private message Visit poster's website 
Display posts from previous:   Sort by:   
Page 1 of 1 [7 Posts]  
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » Advanced Topics » Cutting edge
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.0659s ][ Queries: 12 (0.0070s) ][ GZIP on ]