 |
Puppy Linux Discussion Forum Puppy HOME page : puppylinux.com "THE" alternative forum : puppylinux.info
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in|
The time now is Wed 11 Dec 2013, 14:58 All times are UTC - 4 |
 Forum index » Advanced Topics » Hardware » Printers |
|
How to Install Brother Printers and Scanners
|
 
|
View previous topic :: View next topic |
| Page 5 of 9 [126 Posts] | Goto page: Previous 1, 2, 3, 4, 5, 6, 7, 8, 9 Next |
| Author | Message | ||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
bones01
Joined: 11 Aug 2008 Posts: 367 Location: Melbourne, Aus |
Hi RCRN I've got Precise Puppy up and running, but can't get the printer working. It's a Brother HL-2130. I've tried following your instructions on the front page, and found the relevant .deb files for the printer, but nothing else seems to be working. Could I trouble to make a .pet for this if possible? Thanks for all you do to keep the community connected and working. Bones _________________ Dell Latitude D630 running Puppy 5.2.8 frugal, Macpup 525 frugal (if I can get it working again) Precise Puppy 5.4 live DVD |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
 |
|||||||||||||||||||||||||||||||||
rcrsn51
 Joined: 05 Sep 2006 Posts: 8364 Location: Stratford, Ontario |
Can do. But first, I would like to find out what went wrong with your install. As a test: 1. I downloaded and installed the "debbi" pet. 2. I downloaded the two HL-2130 debs. 3. I ran
4. I checked in CUPS. An HL-2130 printer had been created for me that looked OK. When you looked in CUPS, did you not see the printer? If it was there, did it not work? |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
bones01
Joined: 11 Aug 2008 Posts: 367 Location: Melbourne, Aus |
Thanks rcrsn, I'll try it when I'm home tonight. Cheers. Bones _________________ Dell Latitude D630 running Puppy 5.2.8 frugal, Macpup 525 frugal (if I can get it working again) Precise Puppy 5.4 live DVD |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
bones01
Joined: 11 Aug 2008 Posts: 367 Location: Melbourne, Aus |
Thanks for the extra instructions rcrsn. They worked a treat. When I tried to follow the instructions on the first post, the only results I got in the console were "File could not be found" - or something similar. Anyway, these further instructions were very helpful. So, for the benefit of others, and myself at some later stage, this is what I did: D/L the .deb files and saved in 'root' D/L the debbi.pet and installed Opened a console and typed "debbi hl2130lpr-2.1.0-1.i386.deb" and 'enter' Next, typed " debbi cupswrapperHL2130-2.0.4-2.i386.deb" and 'enter'. Then Menu>Setup>Cups Printer Wizard>Yes When the CUPS page opened, clicked on "Adding Printers and Classes">Add Printer and followed the prompts from there. My printer (Brother HL2130) was shown, so everything flowed simply from there, with the driver listed in the options. Thanks again for your help and guidance. I'm a happy Puppy oncee again 
Enjoy the day. Bones _________________ Dell Latitude D630 running Puppy 5.2.8 frugal, Macpup 525 frugal (if I can get it working again) Precise Puppy 5.4 live DVD |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
rcrsn51
Joined: 05 Sep 2006 Posts: 8364 Location: Stratford, Ontario |
Excellent. For your convenience the next time you need to set up this printer, I have attached a PET below. It will not auto-install the printer in CUPS, so you will need to run the Add Printer procedure.
|
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
bones01
Joined: 11 Aug 2008 Posts: 367 Location: Melbourne, Aus |
Thanks again for your patient help. You are greatly appreciated. Bones _________________ Dell Latitude D630 running Puppy 5.2.8 frugal, Macpup 525 frugal (if I can get it working again) Precise Puppy 5.4 live DVD |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
Sage
Joined: 04 Oct 2005 Posts: 4682 Location: GB |
More Brother printer grief with a friend's HL2240 in Slacko 5.4. Followed the destructions on page-the-first. The Brother website recommended using the 2170w driver. Everything worked like a dream. Printer shows in all the panels (as HL2240) along with it's usual options. It's even in lsusb as itself (2240). Hit print, the usual faint click prior to actual printing emits from the printer. Then silence..... Seem to have done everything that bones did and some, without success. For the record, Mint recognised and installed it without hassle, first attempt. Appreciate any comments, suggestions. Please be advised that my access to this system is severely limited due to friend still working for his living. Thanks. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
rcrsn51
Joined: 05 Sep 2006 Posts: 8364 Location: Stratford, Ontario |
I couldn't find any other reports from you about this printer.
??? I checked the Brother site and there were packages for the HL2240. However, I did some testing and there are definitely problems with the Brother drivers in Slacko 5.4. 1. I tested my Brother HL2070N using the driver built from the Brother sources and it failed. There were no error messages anywhere. This driver works in every other Puppy, including Slacko 5.3 2. I then installed it in Slacko 5.4 as a Gutenprint HL-2060. This worked fine. 3. I then downgraded Ghostscript using this PET. It worked! So there is something slightly different about the version of Ghostscript in Slacko 5.4 that the Brother drivers don't like. However, it works fine with other printer models that I have tested. For your convenience, I have attached a PET for your HL-2240. Unlike the debbi procedure, it does not automatically install a CUPS printer, so you must run the CUPS setup wizard yourself.
Last edited by rcrsn51 on Thu 07 Feb 2013, 18:27; edited 1 time in total |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
Sage
Joined: 04 Oct 2005 Posts: 4682 Location: GB |
Thanks for your prompt response, rc. 'More' didn't refer to mine, but other folks' issues! Yes, the 2240 is indeed there, but when clicked it showed 2170w ! Interested to learn that even you experienced problems - not much hope for YT, then! Most grateful for your intervention and kind effort to produce a .pet. I will endeavour to contact friend at the weekend when they release him from bondage... Hope I can manage to uninstall the present files. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
rcrsn51
Joined: 05 Sep 2006 Posts: 8364 Location: Stratford, Ontario |
Where are you seeing this?
You shouldn't need to. Just install the new PET and Ghostscript. Then delete the old printer from CUPS and let it auto-detect the printer again. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
Sage
Joined: 04 Oct 2005 Posts: 4682 Location: GB |
I think it was direct from the Brother site, but I am not able to confirm from this location. I remember there were three or four printers listed under LPR(?) for the 2240. The first was undesignated, the second was 2240D and I forget the other(s). I chose the first and 2170w popped up as the Brother (recommended) choice. When I installed it, it came up as detecting the 2240, whereas it didn't detect anything prior. Ghostscript? Where from? I will try what you suggest when I get access again. Many thanks. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
rcrsn51
Joined: 05 Sep 2006 Posts: 8364 Location: Stratford, Ontario |
Could you get me a link to this site? Maybe the GB site is different from the US one.
From the link I provided above. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
Sage
Joined: 04 Oct 2005 Posts: 4682 Location: GB |
Ta, again. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
linbie
Joined: 09 Jan 2010 Posts: 59 |
Just a quick note to say thank you Followed your instruction I now have a Brother MFC7362N as a USB printer and a Brother HL-3040CN as a network printer running under Slacko 5.3.1. Many thanks for clear instructions (some of the answers were in posts following the first post) |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
rcrsn51
Joined: 05 Sep 2006 Posts: 8364 Location: Stratford, Ontario |
Excellent. Did you also get network scanning working with your MFC7362N? This model is the first one reported here that uses brscan4. |
||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||
It works
| Page 5 of 9 [126 Posts] | Goto page: Previous 1, 2, 3, 4, 5, 6, 7, 8, 9 Next |
|
|
View previous topic :: View next topic |
|
Forum index » Advanced Topics » Hardware » Printers |
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum |
Powered by phpBB © 2001, 2005 phpBB Group