This is sakura compiled on racy 5.3 on an Asus-1005HAG/HGO netbook frugal installed on micro sd card 1GB RAM, no swap .
They have been compiled simply './configure' OR 'cmake . && make' .
They go to /usr/local/*
They are split into EXE,DOC,DEV,NLS .
The .pets are packed into this single .sfs NOT to be able to load it at boot time, but for simply clicking on the .sfs to access the .pets .
The .pets should install as usual .
Since racy uses a glic-2.10.1 I guess they should run on Lupu/Lucid glibc-2.11.x and Slacko glibc-2.13.x .
I don't expect them to run on Puppy4 glibc-2.6.1 and LighthousePup-443 glibc-2.9.x .
For these Puppies please check out :
Sakura Terminal Emulator
by aragon
sakura-2.3.4-i486.pet
by runtt21
*
Homepage of sakura :
https://launchpad.net/ubuntu/+source/sakura/2.4.2-3
Got vte from here :
http://packages.debian.org/source/sid/vte
*
sakura-2.4.2 + vte-0.28.2
Update :
Just tested the installation on a dpup-005 by iguleder which runs the
stock 'linux_kernel-2.6.33.2-tickless_smp_patched-L3.pet'
with glibc-2.11.2
which came out in the time of Lupu-511
and it worked out_of_the_box just installing the two mains
sakura-2.4.2-i686.pet
vte-0.28.2-i686.pet
from the above attached .sfs
They both have a size of 'ls -s -> 405KB' which should expand to approx. 1,6MB installed .
I like urxvt too, but it is lacking tabs, the possibility for a background image and most important, it is possible to scroll back in sakura even when there is output from for example ' make ' .
A small note : When adjusting the options in sakura, please close sakura and launch it again, for new instances of sakura won't read '$HOME/.config/sakura/sakura.conf' if another instance of sakura is running .
Enjoy !
Just tested the installation on a dpup-005 by iguleder which runs the
stock 'linux_kernel-2.6.33.2-tickless_smp_patched-L3.pet'
with glibc-2.11.2
which came out in the time of Lupu-511
and it worked out_of_the_box just installing the two mains
sakura-2.4.2-i686.pet
vte-0.28.2-i686.pet
from the above attached .sfs
They both have a size of 'ls -s -> 405KB' which should expand to approx. 1,6MB installed .
I like urxvt too, but it is lacking tabs, the possibility for a background image and most important, it is possible to scroll back in sakura even when there is output from for example ' make ' .
A small note : When adjusting the options in sakura, please close sakura and launch it again, for new instances of sakura won't read '$HOME/.config/sakura/sakura.conf' if another instance of sakura is running .
Enjoy !
- Attachments
-
- sakura-2.4.2-pet.png
- (171.66 KiB) Downloaded 1744 times
The opacity can be adjusted by the right-click menu : Options > Set opacity level . The lesser , the more transparent .
For the background : attached default background from iguleders dpup series (007, was last with default 2.6.33.2 kernel, later had 2.6.35/36 kernels ) .
For the background : attached default background from iguleders dpup series (007, was last with default 2.6.33.2 kernel, later had 2.6.35/36 kernels ) .
- Attachments
-
- default.jpg.bz2
- (160.26 KiB) Downloaded 693 times
Just wanted to note, that because of configured to /usr/local i had to run
on one Puppy to make it find the vte libs .
And another thing to mention are windowmanagers like enlightenment e17 or some pure Xserver backgrounds that somehow are not able to work with the transparency option in sakura .
Code: Select all
ldconfig
And another thing to mention are windowmanagers like enlightenment e17 or some pure Xserver backgrounds that somehow are not able to work with the transparency option in sakura .