See this thread for details.
http://www.murga-linux.com/puppy/viewto ... 249#603249
Also, it appears that the line 115200 warning wasn't the significant concern as the same warning appeared with the new modem but didn't hinder the successful use of the modem.
Hello,
I'm setting up PupDial on a Toshiba 1416-S115, RAM 515MB.
I'm using Lucid Puppy-520 full install on HDD.
I'm getting the dreaded:
I checked with provider and verified username and password is correct.*** WARNING! Line "115200"
in /etc/ppp/options may conflict with wvdial!
I tried slowing speed of modem.
I tried *Stupid* mode in various combos with *Auto* mode. I thought the *Stupid* mode would work for sure.
Here is what I know so far:
dmesg says:
phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
wvdial is:
noauth
name wvdial
usepeerdns
wvdial.conf is:
[Dialer Defaults]
Modem = /dev/ttySL0
Baud = 460800
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Carrier Check = no
Dial Command = ATDT
ISDN = 0
Modem Type = Analog Modem
; Phone = <Target Phone Number> Should this be filled in?
; Username = <Your Login Name> Should this be filled in?
; Password = <Your Password> Should this be filled in?
[Dialer isp1]
Phone = 9999999999 I edited out phone, username, password for this post.
Username = xxx@isomedia.com
Password = xxx
Auto Reconnect = yes
[Dialer isp1apn]
Init5 = AT+CGDCONT=1,"IP",""
[Dialer isp2]
Phone = 9999999999 I edited out phone, username, password for this post.
Username = xxx@isomedia.com
Password = xxx
Auto Reconnect = yes
[Dialer isp2apn]
Init5 = AT+CGDCONT=1,"IP",""
[Dialer pin]
Init1 = AT+CPIN=
[Dialer wireless]
#To force only 2G or 3G, uncomment the Init4 line and append 0 (2G) or 2 (3G), and substitute your operator's name for MYOPS. =
#Init4 = AT+COPS=0,0,"MYOPS",
#Init6-Init9 lines are available for user purposes; the commented examples can be used as described: =
#To force the 3G quality of service level, uncomment the Init6/Init7 line pair and set value two places each, for 384k/144k/64k, omitting the "k" (e.g., = 1,4,64,384,64,384).
#To list all the APNs stored in the modem, uncomment the Init8 line; check the Connection status log for lines beginning with +CGDCONT:. =
#To list the operator identifier stored in the modem, uncomment the Init9 line; check the Connection status log for a line beginning with +COPS:. =
#Init6 = AT+CGEQMIN=1,4,64,384,64,384
#Init7 = AT+CGEQREQ=1,4,64,384,64,384
#Init8 = AT+CGDCONT?
options are:
lock
defaultroute
noipdefault
noauth
usepeerdns
modem
#/dev/modem
115200
crtscts
debug
asyncmap 0
name "barney"
Output of Modem Test says:
Scanning your serial ports for a modem.
Port Scan<*1>: S0 S1 S2 S3
ttyS4<Info>: No such device or address
Port Scan<*1>: S4
ttySL0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 4800 baud
ttySL0<*1>: ATQ0 V1 E1 -- OK
ttySL0<*1>: ATQ0 V1 E1 Z -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
ttySL0<*1>: Speed 9600: AT -- OK
ttySL0<*1>: Speed 19200: AT -- OK
ttySL0<*1>: Speed 38400: AT -- OK
ttySL0<*1>: Speed 57600: AT -- OK
ttySL0<*1>: Speed 115200: AT -- OK
ttySL0<*1>: Speed 230400: AT -- OK
ttySL0<*1>: Speed 460800: AT -- OK
ttySL0<*1>: Max speed is 460800; that should be safe.
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found a modem on /dev/ttySL0.
Modem configuration written to /etc/wvdial.conf.
*** WARNING! Line "115200"
in /etc/ppp/options may conflict with wvdial!
ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
I've found plenty of references in the Forum to this error message, however, I have yet to find a fix for this situation.
Is there any other information you may need to clarify the situation?
Thank you in advance for any assistance you can offer.
Screenshot of modem setup: