Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Fri 28 Nov 2014, 15:23
All times are UTC - 4
 Forum index » Advanced Topics » Additional Software (PETs, n' stuff) » Drivers
NVIDIA Drivers for kernel 2.6.30.5 (puppy 4.3)
Post new topic   Reply to topic View previous topic :: View next topic
Page 3 of 4 [52 Posts]   Goto page: Previous 1, 2, 3, 4 Next
Author Message
auriza


Joined: 05 Jan 2009
Posts: 46
Location: Surakarta, Java

PostPosted: Sun 01 Nov 2009, 22:28    Post subject:  

Try:
Code:
# depmod-FULL
# modprobe nvidia
# nvidia-xconfig
# xwin
Back to top
View user's profile Send private message Visit poster's website 
gray


Joined: 23 Feb 2007
Posts: 313
Location: Adelaide - South Australia

PostPosted: Thu 05 Nov 2009, 06:44    Post subject: NVIDIA 190.42  

Updated to latest driver - 190.42. see main post.
Back to top
View user's profile Send private message 
mkksah

Joined: 22 Nov 2009
Posts: 1

PostPosted: Sun 22 Nov 2009, 08:23    Post subject:  

Hi,
I'm new to puppy, everything seems fine but the video adapter.
I'm trying to install NVIDIA-96.43.13-k2.6.30.5-1.pet to puppy 4.3.1 on Compaq Tc1000 tablet with a Geforce2 Go adapter. Install ends "successful", but after restarting x I get a black screen and cannot go back. I have tried browserlinux 3.5.3 (4.1.2 kernel) with correct pet, same
result.
I can't go further to explore and use puppy, need your help...
Back to top
View user's profile Send private message 
thedukesd

Joined: 02 Dec 2009
Posts: 3

PostPosted: Wed 02 Dec 2009, 15:00    Post subject:  

I installed NVIDIA-71.86.11-k2.6.30.5-1.pet on an old pc (TNT2 M64 is the gpu) running puppy linux 4.31 frugall install. Everything worked ok with the install. I restarting x, x failed to start, restarted puppy again x failed to start. After running what auriza said in a previsous post:

Code:
# depmod-FULL
# modprobe nvidia
# nvidia-xconfig
# xwin


X started without any problem after this and so far it didn't do any problems.
Back to top
View user's profile Send private message 
LaneLester

Joined: 14 Sep 2008
Posts: 209
Location: Rural Georgia, USA

PostPosted: Fri 25 Dec 2009, 09:52    Post subject:  

Caneri wrote:
mirror
http://puppylinux.ca/tpp/NOP/

The original URL and this one both require a login for me. Is it me or has something changed?

Lane
Back to top
View user's profile Send private message 
CatDude


Joined: 03 Jan 2007
Posts: 1497
Location: UK

PostPosted: Fri 25 Dec 2009, 10:37    Post subject:  

Hello LaneLester

LaneLester wrote:
Caneri wrote:
mirror
http://puppylinux.ca/tpp/NOP/

The original URL and this one both require a login for me. Is it me or has something changed?

Username = puppy
Password = linux

CatDude
.

_________________

Back to top
View user's profile Send private message 
LaneLester

Joined: 14 Sep 2008
Posts: 209
Location: Rural Georgia, USA

PostPosted: Fri 25 Dec 2009, 12:24    Post subject:  

Thanks, CatDude!

Another Google search (I almost never get help with forum searches) turned up another site that didn't require a password. Regretfully, the driver didn't work for me, and I started a new thread about that adventure.

Lane
Back to top
View user's profile Send private message 
Max Headroom


Joined: 28 Jun 2006
Posts: 187
Location: GodZone Kiwi

PostPosted: Fri 08 Jan 2010, 20:57    Post subject: Please Help...
Subject description: Please Help...
 

I'm having Trouble installing Any NVidia Drivers into NOP so that I can have Me Blinging Compiz-Fusion... on This Toshiba Satyrlite Smile Pro TE2100 1.7 GHz, Pentium 4 w/ 512 MB RAMemory & 16 MB NVidia GeForce4 420 Go Grafix.

I'm Running NOP 4.3.1 w/ a Full install Finally after having a Lot of Trouble Upgrading from NOP 4.1.3 Full install which I Couldn't install grays' NVidia-96.43.7 Pet nor the Latest NVIDIA-Linux-x86-96.43.14-pkg1.run Package from the NVidia Website.

Now having Upgraded to NOP 4.3.1 I've Tried Both Grays NVIDIA-96.43.13-k2.6.30.5 Pet & the Official Proprietary NVidia Run Package, & in All Cases X Wont Run the LCD Screen Changes from Black & then a white band starts from the bottom Horizonal edge & then the Perimeter of the Screen & then the wHole Screen Turns White?!?

Confused What's Happening? Can I Edit the xorg.conf File? Can AnyBody Help Please?

Ps. 'Xcuse & Pa'don Me Lousy Grama! Smile

Last edited by Max Headroom on Fri 15 Jan 2010, 02:19; edited 1 time in total
Back to top
View user's profile Send private message Yahoo Messenger 
disciple

Joined: 20 May 2006
Posts: 6458
Location: Auckland, New Zealand

PostPosted: Fri 15 Jan 2010, 01:11    Post subject:  

If you're still looking for your log file, at least in a standard Puppy it is /var/log/Xorg.0.log

BTW you might like to help people actually read your posts by using a selection of paragraphs, sentence case, shorter sentences or bullet points Wink

_________________
DEATH TO SPREADSHEETS
- - -
Classic Puppy quotes
- - -
Beware the demented serfers!
Back to top
View user's profile Send private message 
gray


Joined: 23 Feb 2007
Posts: 313
Location: Adelaide - South Australia

PostPosted: Mon 18 Jan 2010, 07:32    Post subject: 420 GO  

MaxHeadroom,

The NVidia-96.43.7.pet is for the 2.6.25.16 kernel and so wont work. You need the http://www.puppylinux.asia/tpp/NOP/NVIDIA-96.43.13-k2.6.30.5-1.pet

Unfortunately the latter pet needs an update as the install script makes a depmod call which doesn't work in puppy 4.3.1 it should be depmod-FULL

After installing the pet (or indeed after trying to install the pkg.run file) drop out of X ( ctrl alt backspace) then enter depmod-FULL.

Then enter xwin to restart the X windows.
if it still doesnt work you may have to run nvidia-xconfig
Back to top
View user's profile Send private message 
Max Headroom


Joined: 28 Jun 2006
Posts: 187
Location: GodZone Kiwi

PostPosted: Sat 23 Jan 2010, 07:36    Post subject: G'day Gray, I'm Still Stuck
Subject description: I've been Obedient & Followed All Y'r instructions...
 

Please can U ( or AnyBody eLse ? ), Advise Further Wot's wRong Sad

Xorg.0.log File

X Window System Version 1.3.0
Release Date: 19 April 2007
X Protocol Version 11, Revision 0, Release 1.3
Build Operating System: UNKNOWN
Current Operating System: Linux puppypc 2.6.30.5 #1 SMP Tue Sep 1 15:48:26 GMT-8 2009 i686
Build Date: 28 November 2007
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Jan 24 00:15:53 2010
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) FontPath set to:
/usr/X11R7/lib/X11/fonts/misc/,
/usr/X11R7/lib/X11/fonts/Type1/,
/usr/X11R7/lib/X11/fonts/TTF/
(**) RgbPath set to "/usr/X11R7/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R7/lib/xorg/modules"
(**) Option "RandR" "on"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81d4520
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 1.2
X.Org XInput driver : 0.7
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R7/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.2
(--) using VT number 4

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,1a30 card 1179,0001 rev 04 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 8086,1a31 card 0000,0000 rev 04 class 06,04,00 hdr 01
(II) PCI: 00:1d:0: chip 8086,2482 card 1179,0001 rev 02 class 0c,03,00 hdr 80
(II) PCI: 00:1d:1: chip 8086,2484 card 1179,0001 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1d:2: chip 8086,2487 card 1179,0001 rev 02 class 0c,03,00 hdr 00
(II) PCI: 00:1e:0: chip 8086,2448 card 0000,0000 rev 42 class 06,04,00 hdr 01
(II) PCI: 00:1f:0: chip 8086,248c card 0000,0000 rev 02 class 06,01,00 hdr 80
(II) PCI: 00:1f:1: chip 8086,248a card 1179,0001 rev 02 class 01,01,8a hdr 00
(II) PCI: 00:1f:5: chip 8086,2485 card 1179,0001 rev 02 class 04,01,00 hdr 00
(II) PCI: 00:1f:6: chip 8086,2486 card 1179,0001 rev 02 class 07,03,00 hdr 00
(II) PCI: 01:00:0: chip 10de,0175 card 1179,0001 rev a3 class 03,00,00 hdr 00
(II) PCI: 02:08:0: chip 8086,1031 card 1179,0001 rev 42 class 02,00,00 hdr 00
(II) PCI: 02:0a:0: chip 104c,ac50 card d000,0000 rev 01 class 06,07,00 hdr 02
(II) PCI: 02:0b:0: chip 1179,0617 card d800,0000 rev 32 class 06,07,00 hdr 82
(II) PCI: 02:0b:1: chip 1179,0617 card 1000,0000 rev 32 class 06,07,00 hdr 82
(II) PCI: End of PCI scan
(II) Intel Bridge workaround enabled
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,9), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xdbf00000 - 0xdfffffff (0x4100000) MX[B]
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:30:0), (0,2,12), BCTRL: 0x0000 (VGA_EN is cleared)
(II) Bus 2 I/O range:
[0] -1 0 0x0000d000 - 0x0000dfff (0x1000) IX[B]
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0xfce00000 - 0xfcefffff (0x100000) MX[B]
(II) Bus 2 prefetchable memory range:
[0] -1 0 0x30000000 - 0x3bffffff (0xc000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:31:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-CardBus bridge:
(II) Bus 3: bridge is at (2:10:0), (2,3,4), BCTRL: 0x0540 (VGA_EN is cleared)
(II) Bus 3 I/O range:
[0] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B]
[1] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
(II) Bus 3 prefetchable memory range:
[0] -1 0 0x30000000 - 0x33ffffff (0x4000000) MX[B]
(II) PCI-to-CardBus bridge:
(II) Bus 5: bridge is at (2:11:0), (2,5,Cool, BCTRL: 0x0580 (VGA_EN is cleared)
(II) Bus 5 I/O range:
[0] -1 0 0x0000d800 - 0x0000d8ff (0x100) IX[B]
[1] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
(II) Bus 5 prefetchable memory range:
[0] -1 0 0x34000000 - 0x37ffffff (0x4000000) MX[B]
(II) PCI-to-CardBus bridge:
(II) Bus 9: bridge is at (2:11:1), (2,9,12), BCTRL: 0x0580 (VGA_EN is cleared)
(II) Bus 9 prefetchable memory range:
[0] -1 0 0x38000000 - 0x3bffffff (0x4000000) MX[B]
(--) PCI:*(1:0:0) nVidia Corporation NV17 [GeForce4 420 Go] rev 163, Mem @ 0xfd000000/24, 0xdc000000/26, 0xdbf80000/19
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xe0000000 from 0xefffffff to 0xdfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xfceff000 - 0xfcefffff (0x1000) MX[B]
[1] -1 0 0x3c000000 - 0x3c0003ff (0x400) MX[B]
[2] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[3] -1 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B](B)
[4] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[5] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[6] -1 0 0x0000df40 - 0x0000df7f (0x40) IX[B]
[7] -1 0 0x0000c980 - 0x0000c9ff (0x80) IX[B]
[8] -1 0 0x0000ca00 - 0x0000caff (0x100) IX[B]
[9] -1 0 0x0000cdc0 - 0x0000cdff (0x40) IX[B]
[10] -1 0 0x0000ce00 - 0x0000ceff (0x100) IX[B]
[11] -1 0 0x0000cfa0 - 0x0000cfaf (0x10) IX[B]
[12] -1 0 0x00000374 - 0x00000374 (0x1) IX[B]
[13] -1 0 0x00000170 - 0x00000177 (0x8) IX[B]
[14] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[B]
[15] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[B]
[16] -1 0 0x0000ef60 - 0x0000ef7f (0x20) IX[B]
[17] -1 0 0x0000ef80 - 0x0000ef9f (0x20) IX[B]
[18] -1 0 0x0000efe0 - 0x0000efff (0x20) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xfceff000 - 0xfcefffff (0x1000) MX[B]
[1] -1 0 0x3c000000 - 0x3c0003ff (0x400) MX[B]
[2] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[3] -1 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B](B)
[4] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[5] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[6] -1 0 0x0000df40 - 0x0000df7f (0x40) IX[B]
[7] -1 0 0x0000c980 - 0x0000c9ff (0x80) IX[B]
[8] -1 0 0x0000ca00 - 0x0000caff (0x100) IX[B]
[9] -1 0 0x0000cdc0 - 0x0000cdff (0x40) IX[B]
[10] -1 0 0x0000ce00 - 0x0000ceff (0x100) IX[B]
[11] -1 0 0x0000cfa0 - 0x0000cfaf (0x10) IX[B]
[12] -1 0 0x00000374 - 0x00000374 (0x1) IX[B]
[13] -1 0 0x00000170 - 0x00000177 (0x8) IX[B]
[14] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[B]
[15] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[B]
[16] -1 0 0x0000ef60 - 0x0000ef7f (0x20) IX[B]
[17] -1 0 0x0000ef80 - 0x0000ef9f (0x20) IX[B]
[18] -1 0 0x0000efe0 - 0x0000efff (0x20) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3bffffff (0x3bf00000) MX[B]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3bffffff (0x3bf00000) MX[B]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xfceff000 - 0xfcefffff (0x1000) MX[B]
[5] -1 0 0x3c000000 - 0x3c0003ff (0x400) MX[B]
[6] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[7] -1 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B](B)
[8] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[9] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000df40 - 0x0000df7f (0x40) IX[B]
[13] -1 0 0x0000c980 - 0x0000c9ff (0x80) IX[B]
[14] -1 0 0x0000ca00 - 0x0000caff (0x100) IX[B]
[15] -1 0 0x0000cdc0 - 0x0000cdff (0x40) IX[B]
[16] -1 0 0x0000ce00 - 0x0000ceff (0x100) IX[B]
[17] -1 0 0x0000cfa0 - 0x0000cfaf (0x10) IX[B]
[18] -1 0 0x00000374 - 0x00000374 (0x1) IX[B]
[19] -1 0 0x00000170 - 0x00000177 (0x8) IX[B]
[20] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[B]
[21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[B]
[22] -1 0 0x0000ef60 - 0x0000ef7f (0x20) IX[B]
[23] -1 0 0x0000ef80 - 0x0000ef9f (0x20) IX[B]
[24] -1 0 0x0000efe0 - 0x0000efff (0x20) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/X11R7/lib/xorg/modules/fonts//libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "freetype"
(II) Loading /usr/X11R7/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.3.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "xtrap"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions//libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DEC-XTRAP
(II) LoadModule: "glx"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 96.43.13 Thu Jun 25 18:56:56 PDT 2009
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/X11R7/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "nv"
(II) Loading /usr/X11R7/lib/xorg/modules/drivers//nv_drv.so
(II) Module nv: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 2.1.5
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 1.2
(II) LoadModule: "mouse"
(II) Loading /usr/X11R7/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.2.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) LoadModule: "kbd"
(II) Loading /usr/X11R7/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.2.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) NV: driver for NVIDIA chipsets: RIVA 128, RIVA TNT, RIVA TNT2,
Unknown TNT2, Vanta, RIVA TNT2 Ultra, RIVA TNT2 Model 64,
Aladdin TNT2, GeForce 256, GeForce DDR, Quadro, GeForce2 MX/MX 400,
GeForce2 MX 100/200, GeForce2 Go, Quadro2 MXR/EX/Go,
GeForce2 Integrated GPU, GeForce2 GTS, GeForce2 Ti, GeForce2 Ultra,
Quadro2 Pro, GeForce4 MX 460, GeForce4 MX 440, GeForce4 MX 420,
GeForce4 MX 440-SE, GeForce4 440 Go, GeForce4 420 Go,
GeForce4 420 Go 32M, GeForce4 460 Go, Quadro4 550 XGL,
GeForce4 440 Go 64M, Quadro NVS, Quadro4 500 GoGL,
GeForce4 410 Go 16M, GeForce4 MX 440 with AGP8X,
GeForce4 MX 440SE with AGP8X, GeForce4 MX 420 with AGP8X,
GeForce4 MX 4000, GeForce4 448 Go, GeForce4 488 Go, Quadro4 580 XGL,
Quadro4 NVS 280 SD, Quadro4 380 XGL, Quadro NVS 50 PCI,
GeForce4 448 Go, GeForce4 MX Integrated GPU, GeForce3,
GeForce3 Ti 200, GeForce3 Ti 500, Quadro DCC, GeForce4 Ti 4600,
GeForce4 Ti 4400, GeForce4 Ti 4200, Quadro4 900 XGL, Quadro4 750 XGL,
Quadro4 700 XGL, GeForce4 Ti 4800, GeForce4 Ti 4200 with AGP8X,
GeForce4 Ti 4800 SE, GeForce4 4200 Go, Quadro4 700 GoGL,
Quadro4 980 XGL, Quadro4 780 XGL, GeForce FX 5800 Ultra,
GeForce FX 5800, Quadro FX 2000, Quadro FX 1000,
GeForce FX 5600 Ultra, GeForce FX 5600, GeForce FX 5600XT,
GeForce FX Go5600, GeForce FX Go5650, Quadro FX Go700,
GeForce FX 5200, GeForce FX 5200 Ultra, GeForce FX 5200,
GeForce FX 5200LE, GeForce FX Go5200, GeForce FX Go5250,
GeForce FX 5500, GeForce FX 5100, GeForce FX Go5200 32M/64M,
Quadro NVS 55/280 PCI, Quadro FX 500/600 PCI,
GeForce FX Go53xx Series, GeForce FX Go5100, GeForce FX 5900 Ultra,
GeForce FX 5900, GeForce FX 5900XT, GeForce FX 5950 Ultra,
GeForce FX 5900ZT, Quadro FX 3000, Quadro FX 700,
GeForce FX 5700 Ultra, GeForce FX 5700, GeForce FX 5700LE,
GeForce FX 5700VE, GeForce FX Go5700, GeForce FX Go5700,
Quadro FX Go1000, Quadro FX 1100, GeForce 6800 Ultra, GeForce 6800,
GeForce 6800 LE, GeForce 6800 XE, GeForce 6800 XT, GeForce 6800 GT,
GeForce 6800 GT, GeForce 6800 GS, GeForce 6800 XT, Quadro FX 4000,
GeForce 6800 GS, GeForce 6800, GeForce 6800 LE, GeForce 6800 XT,
GeForce Go 6800, GeForce Go 6800 Ultra, Quadro FX Go1400,
Quadro FX 3450/4000 SDI, Quadro FX 1400, GeForce 6600 GT,
GeForce 6600, GeForce 6600 LE, GeForce 6600 VE, GeForce Go 6600,
GeForce 6610 XL, GeForce Go 6600 TE/6200 TE, GeForce 6700 XL,
GeForce Go 6600, GeForce Go 6600 GT, Quadro FX 550, Quadro FX 550,
Quadro FX 540, GeForce 6200, GeForce 6500,
GeForce 6200 TurboCache(TM), GeForce 6200SE TurboCache(TM),
GeForce 6200 LE, GeForce Go 6200, Quadro NVS 285, GeForce Go 6400,
GeForce Go 6200, GeForce Go 6400, GeForce 6250, GeForce 6800,
GeForce 6800 LE, GeForce 6800 GT, GeForce 6800 XT, GeForce 6200,
GeForce 6200 A-LE, GeForce 7800 GTX, GeForce 7800 GTX,
GeForce 7800 GT, GeForce 7800 GS, GeForce 7800 SLI, GeForce Go 7800,
GeForce Go 7800 GTX, Quadro FX 4500, GeForce 7300 LE,
GeForce 7300 SE, GeForce Go 7200, GeForce Go 7300, GeForce Go 7400,
GeForce Go 7400 GS, Quadro NVS 110M, Quadro NVS 120M, Quadro FX 350M,
GeForce 7500 LE, Quadro FX 350, GeForce 7300 GS, GeForce 7600 GT,
GeForce 7600 GS, GeForce 7300 GT, GeForce 7600 LE, GeForce 7300 GT,
GeForce Go 7700, GeForce Go 7600, GeForce Go 7600 GT,
Quadro NVS 300M, GeForce Go 7900 SE, Quadro FX 550M, Quadro FX 560,
GeForce 7900 GTX, GeForce 7900 GT, GeForce 7900 GS,
GeForce Go 7900 GS, GeForce Go 7900 GTX, Quadro FX 2500M,
Quadro FX 1500M, Quadro FX 5500, Quadro FX 3500, Quadro FX 1500,
Quadro FX 4500 X2, GeForce 6150, GeForce 6150 LE, GeForce 6100,
GeForce Go 6150, GeForce Go 6100, GeForce 8800 GTX, GeForce 8800 GTS,
GeForce 8800 Ultra, Quadro FX 5600, Quadro FX 4600, GeForce 8600 GTS,
GeForce 8600 GT, GeForce 8400 GS, GeForce 8600M GT, GeForce 8700M GT,
Quadro FX 370, Quadro NVS 320M, Quadro FX 570M, Quadro FX 1600M,
Quadro FX 570, Quadro FX 1700, GeForce 8500 GT, GeForce 8400 GS,
GeForce 8300 GS, GeForce 8600M GS, GeForce 8400M GT,
GeForce 8400M GS, GeForce 8400M G, Quadro NVS 140M, Quadro NVS 130M,
Quadro NVS 135M, Quadro FX 360M, Quadro NVS 290
(II) Primary Device is: PCI 01:00:0
(--) Chipset GeForce4 420 Go found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3bffffff (0x3bf00000) MX[B]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xfceff000 - 0xfcefffff (0x1000) MX[B]
[5] -1 0 0x3c000000 - 0x3c0003ff (0x400) MX[B]
[6] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[7] -1 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B](B)
[8] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[9] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000df40 - 0x0000df7f (0x40) IX[B]
[13] -1 0 0x0000c980 - 0x0000c9ff (0x80) IX[B]
[14] -1 0 0x0000ca00 - 0x0000caff (0x100) IX[B]
[15] -1 0 0x0000cdc0 - 0x0000cdff (0x40) IX[B]
[16] -1 0 0x0000ce00 - 0x0000ceff (0x100) IX[B]
[17] -1 0 0x0000cfa0 - 0x0000cfaf (0x10) IX[B]
[18] -1 0 0x00000374 - 0x00000374 (0x1) IX[B]
[19] -1 0 0x00000170 - 0x00000177 (0x8) IX[B]
[20] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[B]
[21] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[B]
[22] -1 0 0x0000ef60 - 0x0000ef7f (0x20) IX[B]
[23] -1 0 0x0000ef80 - 0x0000ef9f (0x20) IX[B]
[24] -1 0 0x0000efe0 - 0x0000efff (0x20) IX[B]
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3bffffff (0x3bf00000) MX[B]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xfceff000 - 0xfcefffff (0x1000) MX[B]
[5] -1 0 0x3c000000 - 0x3c0003ff (0x400) MX[B]
[6] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[7] -1 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B](B)
[8] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[9] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[10] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[11] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[12] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000df40 - 0x0000df7f (0x40) IX[B]
[16] -1 0 0x0000c980 - 0x0000c9ff (0x80) IX[B]
[17] -1 0 0x0000ca00 - 0x0000caff (0x100) IX[B]
[18] -1 0 0x0000cdc0 - 0x0000cdff (0x40) IX[B]
[19] -1 0 0x0000ce00 - 0x0000ceff (0x100) IX[B]
[20] -1 0 0x0000cfa0 - 0x0000cfaf (0x10) IX[B]
[21] -1 0 0x00000374 - 0x00000374 (0x1) IX[B]
[22] -1 0 0x00000170 - 0x00000177 (0x8) IX[B]
[23] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[B]
[24] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[B]
[25] -1 0 0x0000ef60 - 0x0000ef7f (0x20) IX[B]
[26] -1 0 0x0000ef80 - 0x0000ef9f (0x20) IX[B]
[27] -1 0 0x0000efe0 - 0x0000efff (0x20) IX[B]
[28] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[29] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R7/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.2
(II) NV(0): Initializing int10
(II) NV(0): Primary V_BIOS segment is: 0xc000
(--) NV(0): Chipset: "GeForce4 420 Go"
(**) NV(0): Depth 24, (--) framebuffer bpp 32
(==) NV(0): RGB weight 888
(==) NV(0): Default visual is TrueColor
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R7/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 1.2
(==) NV(0): Using HW cursor
(--) NV(0): Linear framebuffer at 0xDC000000
(--) NV(0): MMIO registers at 0xFD000000
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"(II) Module already built-in
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"(II) Module already built-in
(II) NV(0): I2C bus "DDC" initialized.
(II) NV(0): Probing for analog device on output A...
(--) NV(0): ...can't find one
(II) NV(0): Probing for analog device on output B...
(--) NV(0): ...can't find one
(II) NV(0): Probing for EDID on I2C bus A...
(II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) NV(0): I2C device "DDC:ddc2" removed.
(II) NV(0): ... none found
(II) NV(0): Probing for EDID on I2C bus B...
(II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) NV(0): I2C device "DDC:ddc2" removed.
(II) NV(0): ... none found
(--) NV(0): CRTC 1 is currently programmed for DFP
(II) NV(0): Using DFP on CRTC 1
(--) NV(0): Panel size is 1024 x 768
(II) NV(0): Panel is LVDS
(--) NV(0): VideoRAM: 16384 kBytes
(==) NV(0): Using gamma correction (1.0, 1.0, 1.0)
(II) NV(0): Monitor0: Using hsync range of 31.50-38.00 kHz
(II) NV(0): Monitor0: Using vrefresh range of 40.00-60.00 Hz
(II) NV(0): Clock range: 12.00 to 350.00 MHz
(II) NV(0): Not using default mode "640x350" (vrefresh out of range)
(II) NV(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "640x400" (vrefresh out of range)
(II) NV(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "720x400" (vrefresh out of range)
(II) NV(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "640x480" (vrefresh out of range)
(II) NV(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "640x480" (vrefresh out of range)
(II) NV(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "640x480" (hsync out of range)
(II) NV(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "800x600" (hsync out of range)
(II) NV(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "800x600" (hsync out of range)
(II) NV(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "800x600" (hsync out of range)
(II) NV(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1024x768" (hsync out of range)
(II) NV(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1024x768" (hsync out of range)
(II) NV(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1024x768" (hsync out of range)
(II) NV(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1024x768" (hsync out of range)
(II) NV(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1152x864" (exceeds panel dimensions)
(II) NV(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) NV(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1280x960" (exceeds panel dimensions)
(II) NV(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) NV(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) NV(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(II) NV(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(II) NV(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1792x1344" (exceeds panel dimensions)
(II) NV(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1792x1344" (exceeds panel dimensions)
(II) NV(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1856x1392" (exceeds panel dimensions)
(II) NV(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1856x1392" (exceeds panel dimensions)
(II) NV(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) NV(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) NV(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "832x624" (hsync out of range)
(II) NV(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1152x768" (exceeds panel dimensions)
(II) NV(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) NV(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(II) NV(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1600x1024" (exceeds panel dimensions)
(II) NV(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1920x1440" (exceeds panel dimensions)
(II) NV(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "2048x1536" (exceeds panel dimensions)
(II) NV(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "2048x1536" (exceeds panel dimensions)
(II) NV(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) NV(0): Not using driver mode "1024x768" (hsync out of range)
(--) NV(0): Virtual size is 800x600 (pitch 800)
(**) NV(0): *Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) NV(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
(**) NV(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) NV(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
(**) NV(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 59.9 Hz
(II) NV(0): Modeline "640x480" 25.18 640 656 752 800 480 490 492 525 -hsync -vsync
(==) NV(0): DPI set to (75, 75)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R7/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R7/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.3.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 1.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module already built-in
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B]
[1] 0 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B]
[2] 0 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B]
[3] -1 0 0x00100000 - 0x3bffffff (0x3bf00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xfceff000 - 0xfcefffff (0x1000) MX[B]
[8] -1 0 0x3c000000 - 0x3c0003ff (0x400) MX[B]
[9] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[10] -1 0 0xdbf80000 - 0xdbffffff (0x80000) MX[B](B)
[11] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[12] -1 0 0xfd000000 - 0xfdffffff (0x1000000) MX[B](B)
[13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0 0x0000df40 - 0x0000df7f (0x40) IX[B]
[19] -1 0 0x0000c980 - 0x0000c9ff (0x80) IX[B]
[20] -1 0 0x0000ca00 - 0x0000caff (0x100) IX[B]
[21] -1 0 0x0000cdc0 - 0x0000cdff (0x40) IX[B]
[22] -1 0 0x0000ce00 - 0x0000ceff (0x100) IX[B]
[23] -1 0 0x0000cfa0 - 0x0000cfaf (0x10) IX[B]
[24] -1 0 0x00000374 - 0x00000374 (0x1) IX[B]
[25] -1 0 0x00000170 - 0x00000177 (0x8) IX[B]
[26] -1 0 0x000003f4 - 0x000003f4 (0x1) IX[B]
[27] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[B]
[28] -1 0 0x0000ef60 - 0x0000ef7f (0x20) IX[B]
[29] -1 0 0x0000ef80 - 0x0000ef9f (0x20) IX[B]
[30] -1 0 0x0000efe0 - 0x0000efff (0x20) IX[B]
[31] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[32] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(==) NV(0): Write-combining range (0xdc000000,0x1000000)
(II) NV(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Scanline Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
20 256x256 slots
6 512x512 slots
(==) NV(0): Backing store disabled
(==) NV(0): Silken mouse enabled
(WW) NV(0): Option "PreferredMode" is not used
(**) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)
(**) Option "Protocol" "IMPS/2"
(**) Mouse0: Device: "/dev/mouse"
(**) Mouse0: Protocol: "IMPS/2"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/mouse"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 9
(**) Mouse0: Sensitivity: 1
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc102"
(**) Keyboard0: XkbModel: "pc102"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) Mouse0: ps2EnableDataReporting: succeeded

Xorg.conf File

#Special base config file used in Puppy Linux.

# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the font modules
Load "type1"
Load "freetype"

# This loads xtrap extension, used by xrandr
Load "xtrap"

# This loads the GLX module (if present)
Load "glx"

# This loads dri module (if present)
Load "dri"

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R7/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)

FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option "DontVTSwitch"

# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...

Option "RandR" "on"

EndSection

#everything past here is auto-generated by Puppy's Xorg Wizard...


Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "us" #xkeymap0
EndSection

Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection

Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5-38
VertRefresh 40-60
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode" "PREFERREDMODE0"
EndSection

Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection

Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nv" #card0driver
VendorName "nVidia Corporation"
BoardName "NV17 [GeForce4 420 Go]"
BusID "PCI:1:0:0"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
Subsection "Display"
Depth 24
Modes "800x600"
EndSubsection
EndSection

#PuppyHardwareProfile=NVidia

NVidia File Generated that Washes Out!

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder63) Thu Jun 25 18:57:07 PDT 2009

#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
# **********************************************************************
# Server flags section.
# **********************************************************************
#everything past here is auto-generated by Puppy's Xorg Wizard...
#PuppyHardwareProfile=NVidia

Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
RgbPath "/usr/X11R7/lib/X11/rgb"
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection

Section "Module"

# This loads the DBE extension module.
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
# This loads the font modules
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "type1"
Load "freetype"
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (if present)
Load "glx"
# This loads dri module (if present)
EndSection

Section "ServerFlags"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "us" #xkeymap0
EndSection

Section "InputDevice"

#Option "Emulate3Timeout" "50"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection

Section "Modes"

#modes0modeline0
Identifier "Modes0"
EndSection

Section "Monitor"

#UseModes "Modes0" #monitor0usemodes
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5 - 38.0
VertRefresh 40.0 - 60.0
Option "PreferredMode" "PREFERREDMODE0"
EndSection

Section "Device"

### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
#card0driver
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "NV17 [GeForce4 420 Go]"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
Option "RenderAccel" "True"
Option "AllowGLXWithComposite" "True"
Option "AddARGBGLXVisuals" "True"
Option "DisableGLXRootClipping" "True"
SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
EndSection

Section "Extensions"
Option "Composite" "Enable"
EndSection

Nb Also when issue "nvidia-config" Command I get command not found
glxinfo & lsmod commands in Terminal Screenshot.png
 Description   
 Filesize   379.42 KB
 Viewed   735 Time(s)

glxinfo & lsmod commands in Terminal Screenshot.png

Back to top
View user's profile Send private message Yahoo Messenger 
scottf

Joined: 31 Jan 2010
Posts: 2

PostPosted: Mon 01 Feb 2010, 00:10    Post subject: nvidia shows installed but not working  

Hi,

I am running 4.31, full install on a 800MHz Celeron, 256MB RAM. I have a GeForce2 MX400 card.

I have tried the .pet package with no success. I have also tried the driver from the Nvidia site with the devx431 module using the instructions by Iguleder. Both times from a clean install. My xorg.conf file shows the driver as "nvidia".

When I reboot I am back to the VESA driver although the xorg.conf file still shows "nvidia". When I try to run nvidia-xconfig I get an "unable to parse" error message and it does not run.

When I run nvidia-settings the GUI window pops up but there are no options to change and this is displayed in the console window:

ERROR: NV-CONTROL extension not found on this display.
ERROR: Unable to determine number of NVIDIA GPUs on ':0.0'.
ERROR: Unable to determine number of NVIDIA Frame Lock Devices on ':0.0'.
ERROR: Unable to determine number of NVIDIA VCSCs on ':0.0'.

This is what is returned after running nvidia-xconfig:

Using X configuration file: "/etc/X11/xorg.conf".
WARNING: Unable to parse X.Org version string.
sh: line 1: 4271 Broken pipe PATH=usr/X11R6:/bin:/usr/bin:/sbin:/usr/sbin:/usr/X11R6/bin:/usr/bin/X11:$PATH X -version 2>&1
Backup up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup'
New X configuration file written to '/etc/X11/xorg.conf'

The new xorg.conf is identical to the previous one and still shows 'nvidia' as the driver.



What would be my next step?
Back to top
View user's profile Send private message 
scottf

Joined: 31 Jan 2010
Posts: 2

PostPosted: Mon 01 Feb 2010, 16:15    Post subject: Re: nvidia shows installed but not working  

I meant to mention the GeForce2 is a PCI card.

scottf wrote:
Hi,

I am running 4.31, full install on a 800MHz Celeron, 256MB RAM. I have a GeForce2 MX400 card.

I have tried the .pet package with no success. I have also tried the driver from the Nvidia site with the devx431 module using the instructions by Iguleder. Both times from a clean install. My xorg.conf file shows the driver as "nvidia".

When I reboot I am back to the VESA driver although the xorg.conf file still shows "nvidia". When I try to run nvidia-xconfig I get an "unable to parse" error message and it does not run.

When I run nvidia-settings the GUI window pops up but there are no options to change and this is displayed in the console window:

ERROR: NV-CONTROL extension not found on this display.
ERROR: Unable to determine number of NVIDIA GPUs on ':0.0'.
ERROR: Unable to determine number of NVIDIA Frame Lock Devices on ':0.0'.
ERROR: Unable to determine number of NVIDIA VCSCs on ':0.0'.

This is what is returned after running nvidia-xconfig:

Using X configuration file: "/etc/X11/xorg.conf".
WARNING: Unable to parse X.Org version string.
sh: line 1: 4271 Broken pipe PATH=usr/X11R6:/bin:/usr/bin:/sbin:/usr/sbin:/usr/X11R6/bin:/usr/bin/X11:$PATH X -version 2>&1
Backup up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup'
New X configuration file written to '/etc/X11/xorg.conf'

The new xorg.conf is identical to the previous one and still shows 'nvidia' as the driver.



What would be my next step?
Back to top
View user's profile Send private message 
Max Headroom


Joined: 28 Jun 2006
Posts: 187
Location: GodZone Kiwi

PostPosted: Thu 04 Feb 2010, 04:58    Post subject: AnyBody Please Got Any Answers 2 My Problem, Please???
Subject description: AnyBody Please Got Any Answers 2 My Problem, Please???
 

Confused AnyBody Please Got Any Answers 2 My Problem, Please???
I'm Still in Limbo...
Back to top
View user's profile Send private message Yahoo Messenger 
bobie

Joined: 20 Oct 2009
Posts: 6

PostPosted: Fri 12 Feb 2010, 00:02    Post subject:  

I AM TIRED FOR THE SIS740 CHIP SET ON MY BOARD,SO I BUY A ELSA GF2 400 DISPLAY CARD TO IMPROVE THE PERFORMENCE FOR YOUTUBE ,IT JUST LIKE THE SLIDESHOW WHEN I USE THE SIS740.BUT I TRIED THE DRIVER.THREE TIMES. IT DOES NOT WORKS. CAN SOMEONE HELP ME.
Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 3 of 4 [52 Posts]   Goto page: Previous 1, 2, 3, 4 Next
Post new topic   Reply to topic View previous topic :: View next topic
 Forum index » Advanced Topics » Additional Software (PETs, n' stuff) » Drivers
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group
[ Time: 0.2318s ][ Queries: 13 (0.0054s) ][ GZIP on ]