Display resolution set to 1280 X 1024 but still doesn't fit
Display resolution set to 1280 X 1024 but still doesn't fit
my monitor display should be 1280 X 1024 @60Hz
On Puppy, it is set that way but the display is short by between 30 and 40 pixels on the right and left sides. I'm wondering what can be done about that. I have Puppy 4.1 and my settings are saved to a pen drive. I also have the NVidia driver installed for my GeForce FX 5200 graphics card and I use X.org.
On Puppy, it is set that way but the display is short by between 30 and 40 pixels on the right and left sides. I'm wondering what can be done about that. I have Puppy 4.1 and my settings are saved to a pen drive. I also have the NVidia driver installed for my GeForce FX 5200 graphics card and I use X.org.
- Argolance
- Posts: 3767
- Joined: Sun 06 Jan 2008, 22:57
- Location: PORT-BRILLET (Mayenne - France)
- Contact:
Hello gymnart,
I had the same problem because my NVIDIA driver was not the latest one !
Try this :
http://files.wildspad.com/afecelis/linu ... .25.16.pet
Regards
I had the same problem because my NVIDIA driver was not the latest one !
Try this :
http://files.wildspad.com/afecelis/linu ... .25.16.pet
Regards
I take it that you can't simply adjust the monitor settings?
Do you know a good gtkdialog program? Please post a link here
Classic Puppy quotes
ROOT FOREVER
GTK2 FOREVER
Classic Puppy quotes
ROOT FOREVER
GTK2 FOREVER
- piratesmack
- Posts: 100
- Joined: Wed 16 Sep 2009, 14:22
From Puppy:
From SuSE:
Code: Select all
#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (if present)
Load "glx"
# This loads dri module (if present)
Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "us" #xkeymap0
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
#DisplaySize 380 300 # mm
Identifier "Monitor0"
VendorName "SAM"
ModelName "SyncMaster"
### Comment all HorizSync and VertRefresh values to use DDC:
Option "DPMS"
HorizSync 30.0-81.0
VertRefresh 56.0-71.0
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode" "1280x1024"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nv" #card0driver
VendorName "nVidia Corporation"
BoardName "NV34 [GeForce FX 5200]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
Subsection "Display"
Depth 16
Modes "1280x1024"
EndSubsection
EndSection
#PuppyHardwareProfile=NVIDIASyncMaster
Code: Select all
# /.../
# SaX generated X11 config file
# Created on: 2007-04-13T16:01:46-0400.
#
# Version: 7.1
# Contact: Marcus Schaefer <sax@suse.de>, 2002
#
# Automatically generated by [ISaX] (7.1)
# PLEASE DO NOT EDIT THIS FILE!
#
Section "Files"
FontPath "/usr/X11R6/lib/X11/fonts/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/local"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/URW"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo"
FontPath "/usr/X11R6/lib/X11/fonts/PEX"
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/latin2/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/latin7/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/baekmuk:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/japanese:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/kwintv"
FontPath "/usr/X11R6/lib/X11/fonts/truetype"
FontPath "/usr/X11R6/lib/X11/fonts/uni:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/CID"
FontPath "/usr/X11R6/lib/X11/fonts/ucs/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/ucs/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/ucs/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/75dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/100dpi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/hellas/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/misc/sgi:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/xtest"
FontPath "/opt/kde3/share/fonts"
InputDevices "/dev/ttyS0"
InputDevices "/dev/ttyS1"
InputDevices "/dev/ttyS2"
InputDevices "/dev/ttyS3"
InputDevices "/dev/ttyS4"
InputDevices "/dev/ttyS5"
InputDevices "/dev/ttyS6"
InputDevices "/dev/ttyS7"
InputDevices "/dev/ttyS8"
InputDevices "/dev/psaux"
InputDevices "/dev/logibm"
InputDevices "/dev/sunmouse"
InputDevices "/dev/atibm"
InputDevices "/dev/amigamouse"
InputDevices "/dev/atarimouse"
InputDevices "/dev/inportbm"
InputDevices "/dev/gpmdata"
InputDevices "/dev/mouse"
InputDevices "/dev/usbmouse"
InputDevices "/dev/adbmouse"
InputDevices "/dev/input/mice"
InputDevices "/dev/input/event0"
InputDevices "/dev/pointer0"
InputDevices "/dev/pointer1"
InputDevices "/dev/pointer2"
InputDevices "/dev/pointer3"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "freetype"
Load "extmod"
Load "glx"
Load "v4l"
EndSection
Section "InputDevice"
Driver "kbd"
Identifier "Keyboard[0]"
Option "Protocol" "Standard"
Option "XkbLayout" "us"
Option "XkbModel" "pc104"
Option "XkbRules" "xfree86"
EndSection
Section "InputDevice"
Driver "mouse"
Identifier "Mouse[1]"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Name" "ImPS/2 Generic Wheel Mouse"
Option "Protocol" "explorerps/2"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
DisplaySize 377 301
HorizSync 30-81
Identifier "Monitor[0]"
ModelName "SYNCMASTER 4S"
Option "DPMS"
VendorName "SAMSUNG"
VertRefresh 56-75
UseModes "Modes[0]"
EndSection
Section "Modes"
Identifier "Modes[0]"
Modeline "1280x1024" 134.72 1280 1368 1504 1728 1024 1025 1028 1068
Modeline "1280x1024" 114.54 1280 1360 1496 1712 1024 1025 1028 1062
Modeline "1280x960" 126.27 1280 1368 1504 1728 960 961 964 1001
Modeline "1280x960" 107.32 1280 1360 1496 1712 960 961 964 995
Modeline "1280x800" 104.35 1280 1360 1496 1712 800 801 804 835
Modeline "1280x800" 88.68 1280 1352 1488 1696 800 801 804 830
Modeline "1152x864" 102.08 1152 1224 1352 1552 864 865 868 901
Modeline "1152x864" 86.70 1152 1224 1344 1536 864 865 868 896
Modeline "1280x768" 99.17 1280 1352 1488 1696 768 769 772 801
Modeline "1280x768" 84.35 1280 1344 1480 1680 768 769 772 797
Modeline "1024x768" 79.52 1024 1080 1192 1360 768 769 772 801
Modeline "1024x768" 67.48 1024 1080 1184 1344 768 769 772 797
Modeline "800x600" 47.53 800 840 920 1040 600 601 604 626
Modeline "800x600" 40.19 800 832 912 1024 600 601 604 623
Modeline "768x576" 43.52 768 800 880 992 576 577 580 601
Modeline "768x576" 37.37 768 800 880 992 576 577 580 598
Modeline "640x480" 29.84 640 664 728 816 480 481 484 501
Modeline "640x480" 25.10 640 656 720 800 480 481 484 498
EndSection
Section "Screen"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
Section "Device"
BoardName "GeForce FX 5200 (0x0322)"
BusID "1:0:0"
Driver "nvidia"
Identifier "Device[0]"
Screen 0
VendorName "NVidia"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
Section "Extensions"
EndSection
- piratesmack
- Posts: 100
- Joined: Wed 16 Sep 2009, 14:22
Well, it looks like your xorg is configured to use the nv driver and not the nvidia driver (probably why opengl isn't working also)
So try this:
In the "Device" section of puppy's xorg, change
To
Then restart X and see if it helped.
If that doesn't work, try using this xorg.conf:
So try this:
In the "Device" section of puppy's xorg, change
Code: Select all
Driver "nv" #card0driver
Code: Select all
Driver "nvidia" #card0driver
If that doesn't work, try using this xorg.conf:
Code: Select all
#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (if present)
Load "glx"
# This loads dri module (if present)
Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "us" #xkeymap0
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
DisplaySize 377 301 # mm
Identifier "Monitor0"
VendorName "SAM"
ModelName "SyncMaster"
### Comment all HorizSync and VertRefresh values to use DDC:
Option "DPMS"
#HorizSync 30.0-81.0
VertRefresh 56-75
UseModes "Modes0" #monitor0usemodes
#Option "PreferredMode" "1280x1024"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
Modeline "1280x1024" 134.72 1280 1368 1504 1728 1024 1025 1028 1068
Modeline "1280x1024" 114.54 1280 1360 1496 1712 1024 1025 1028 1062
Modeline "1280x960" 126.27 1280 1368 1504 1728 960 961 964 1001
Modeline "1280x960" 107.32 1280 1360 1496 1712 960 961 964 995
Modeline "1280x800" 104.35 1280 1360 1496 1712 800 801 804 835
Modeline "1280x800" 88.68 1280 1352 1488 1696 800 801 804 830
Modeline "1152x864" 102.08 1152 1224 1352 1552 864 865 868 901
Modeline "1152x864" 86.70 1152 1224 1344 1536 864 865 868 896
Modeline "1280x768" 99.17 1280 1352 1488 1696 768 769 772 801
Modeline "1280x768" 84.35 1280 1344 1480 1680 768 769 772 797
Modeline "1024x768" 79.52 1024 1080 1192 1360 768 769 772 801
Modeline "1024x768" 67.48 1024 1080 1184 1344 768 769 772 797
Modeline "800x600" 47.53 800 840 920 1040 600 601 604 626
Modeline "800x600" 40.19 800 832 912 1024 600 601 604 623
Modeline "768x576" 43.52 768 800 880 992 576 577 580 601
Modeline "768x576" 37.37 768 800 880 992 576 577 580 598
Modeline "640x480" 29.84 640 664 728 816 480 481 484 501
Modeline "640x480" 25.10 640 656 720 800 480 481 484 498
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nvidia" #card0driver
VendorName "nVidia Corporation"
BoardName "NV34 [GeForce FX 5200]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1024x768" "800x600" "768x576" "640x480"
EndSubSection
EndSection
#PuppyHardwareProfile=NVIDIASyncMaster
ok, I tried that but it looks like puppy is not using the new one. It looks like it went back to using the previous one and "insists" on use the nv driver and not "nvidia".
Can I uninstall this newer driver? After that, can I install the older one without rebooting or something? That's what I think I will try.
Can I uninstall this newer driver? After that, can I install the older one without rebooting or something? That's what I think I will try.
Well ok, now I have that newer Nvidia driver uninstalled (I think) and I'm pretty sure that I'm back to the older one (173.14.12-k2.6.25.16) but still, OpenGL is not working. I did a dependency check for Armagetron and it said that it was missing libgluso.1. When I try using SweetHome3D, it still tells me that I should update my directx/opengl drivers. I did not get this message before trying out that newer nvidia driver (177.82-k2.6.25.16)
Nvidia settings don't even show up in the menu like it used to before I tried that newer driver.
On top of all that, when I boot back into SuSE, the boot screen is moved over to the left too far now! It was not like that before, it used to be nicely centered. Once I'm all booted into SuSE, then the display seems to be ok. When I'm shutting it down, that shutting down screen is moved too far over to the left.
This is the Device section of Puppy's X11.conf:
Like I said, when I had tried to edit it, Puppy didn't seem to use it, the file seemed to just go back to the info it had before.
Nvidia settings don't even show up in the menu like it used to before I tried that newer driver.
On top of all that, when I boot back into SuSE, the boot screen is moved over to the left too far now! It was not like that before, it used to be nicely centered. Once I'm all booted into SuSE, then the display seems to be ok. When I'm shutting it down, that shutting down screen is moved too far over to the left.
This is the Device section of Puppy's X11.conf:
Code: Select all
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nv" #card0driver
VendorName "nVidia Corporation"
BoardName "NV34 [GeForce FX 5200]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
Subsection "Display"
Depth 16
Modes "1280x1024"
EndSubsection
EndSection
#PuppyHardwareProfile=NVIDIASyncMaster
You might check to see whether or not your monitor has an automatic-adjust feature. That way, it might attempt to set the screen properly for both distros.gymnart wrote:@disciple: no, I can't adjust the monitor because I use it on SuSE and everything works/looks fine with that distro. If I change anything to suit puppy, then the settings will be messed up for SuSE.
[ Puppy 4.3.1 JP, Frugal install ] * [ XenialPup 7.5, Frugal install ] * [XenialPup 64 7.5, Frugal install] * [ 4GB RAM | 512MB swap ]
In memory of our beloved American Eskimo puppy (1995-2010) and black Lab puppy (1997-2011).
In memory of our beloved American Eskimo puppy (1995-2010) and black Lab puppy (1997-2011).
Yes, my son-in-law found it and adjusted it while SuSE was booting up and it said "auto adjust in progress". I hope it stays put next time I boot SuSE.
It does not seem to auto adjust for Puppy though and I am still concerned that if I mess with the monitor settings, that it would affect the settings for SuSE. (the monitor is a Samsung SyncMaster 930B)
Anyway, since OpenGL no longer works on my puppy now, I think I will delete this save file and replace it with my previously saved session (before the driver update attempt.)
It does not seem to auto adjust for Puppy though and I am still concerned that if I mess with the monitor settings, that it would affect the settings for SuSE. (the monitor is a Samsung SyncMaster 930B)
Anyway, since OpenGL no longer works on my puppy now, I think I will delete this save file and replace it with my previously saved session (before the driver update attempt.)
FWIW the "correct" answer to the original question should be:
- Menu
- Setup
- Xorg Video Wizard
- xvidtune
- play with the settings
- Menu
- Setup
- Xorg Video Wizard
- xvidtune
- play with the settings
Do you know a good gtkdialog program? Please post a link here
Classic Puppy quotes
ROOT FOREVER
GTK2 FOREVER
Classic Puppy quotes
ROOT FOREVER
GTK2 FOREVER