Puppy Linux Discussion Forum Forum Index Puppy Linux Discussion Forum
Puppy HOME page : puppylinux.com
"THE" alternative forum : puppylinux.info

READ-ONLY-MODE: PLEASE DO NOT POST NEW STUFF!
  New Forum: http://forum.puppylinux.com
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups    
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

The time now is Fri 14 Aug 2020, 14:29
All times are UTC - 4

 Forum index » Advanced Topics » Hardware » Networking » Wireless
wireless / wifi cards confirmed to work in puppy - OLD LIST
This forum is locked: you cannot post, reply to, or edit topics.   This topic is locked: you cannot edit posts or make replies. View previous topic :: View next topic
Page 13 of 13 [186 Posts]   Goto page: Previous 1, 2, 3, ..., 11, 12, 13
Author Message
five

Joined: 15 Jul 2009
Posts: 5
PostPosted: Sat 18 Jul 2009, 00:23    Post subject:  
Linksys WPC600N, confirmed working, using these drivers. I've tested it on both WPA2 (AES) and unencrypted networks. Both worked just fine, no problems at all.
Back to top
View user's profile Send private message 
jackieflorida


Joined: 28 May 2008
Posts: 122
Location: MIAMI
PostPosted: Sun 19 Jul 2009, 10:44    Post subject:  
Using Puppy Linux 4.1.2 on an old Gateway Solo 9100 laptop.
HEGU, a cheap Chinese PCMCIA wifi adapter confirmed to work with WEP, WPA, and WPA2 (confirmed and edited 9/11/09) via Puppy Linux native Broadcom b43legacy driver that loads automatically.
For under $12 delivered, I was pleasantly surprised.
See it here:http://www.dealextreme.com/details.dx/sku.13731

The included .zip Windows drivers were incorrect. I didn't check the included .rar drivers.

I continue to very much like this PCMCIA wifi adapter and just leave it in the old laptop's slot permanently. It does stick out about an inch so some precaution about it is needed, but that's easy. That is why I prefer it to a USB adapter which presents physical demands. I've upgraded to Puppy 4.2.1 with no problems.

Having seen Fishback's really nice compilation posted below, and in response to his suggestions, I invoked Menu/System/PupScanInterfaceInformation and retrieved these details:
Code:
DESCRIPTION: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller
VENDOR: 14e4  DEVICE: 4320  KERNEL MODULE: bcm43xx

In the PuppyNetworkWizard the module stated is b43legacy as reported above is the one that works. The bcm43xx modules did not work. The WPA2 is more specifically on the router as:
WPA2 Personal AES.

Regarding encryption and securing your wifi network check this:
http://www.komando.com/tips/index.aspx?id=7281
Last edited by jackieflorida on Fri 11 Sep 2009, 10:46; edited 3 times in total
Back to top
View user's profile Send private message 
johnheav

Joined: 21 Jun 2009
Posts: 5
PostPosted: Wed 22 Jul 2009, 13:19    Post subject: Linksys WUSB54GC works...
Subject description: ....under Puppy 4.2.1...		  
The Linksys WUSB54GC USB adapter works under Puppy 4.2.1. I use PWireless for the wireless interface. Puppy knows the driver to install, there's nothing for the user to do except boot up, connect, and GO!

Oddly enough, I can't get it to install properly under XP. Go figure.
Back to top
View user's profile Send private message 
Tanuvan

Joined: 22 Jul 2009
Posts: 3
PostPosted: Wed 22 Jul 2009, 18:47    Post subject: Re: Linksys WUSB54GC works...
Subject description: ....under Puppy 4.2.1...		  
johnheav wrote:
The Linksys WUSB54GC USB adapter works under Puppy 4.2.1. I use PWireless for the wireless interface. Puppy knows the driver to install, there's nothing for the user to do except boot up, connect, and GO!

Oddly enough, I can't get it to install properly under XP. Go figure.


I am using the same adapter and same version of puppy. It works for a while and then locks up Puppy. In order to shutdown, I have to pull the power cord Sad

It only happens with this particular USB adapter model.

I attempted to use the ndiswrapper instead, and the same thing occurs.
Back to top
View user's profile Send private message 
NHArticleTen

Joined: 23 Mar 2009
Posts: 1
PostPosted: Wed 22 Jul 2009, 21:46    Post subject: Acer Aspire One AOA-150-1864
Subject description: Dell Wireless 1390 WLAN mini card working with Puppy 4.2.1		  
Acer Aspire One AOA-150-1864

Dell Wireless 1390 WLAN mini card working with Puppy 4.2.1

Triple-booting(grub) XP Pro SP3, Ubuntu 9.04 full version Jaunty, and Puppy 4.2.1

did all my LiveCD work with an old cd-rom drive and one of those multi-cables from Coolmax via Newegg
(http://www.newegg.com/Product/Product.aspx?Item=N82E16812104062)

works great...and I've still got five logical partitions for five more *nix distros!

screen is a little small and hard on the old guy's eyes...lol.

.
Back to top
View user's profile Send private message 
Pizzasgood


Joined: 04 May 2005
Posts: 6266
Location: Knoxville, TN, USA
PostPosted: Sat 03 Oct 2009, 15:02    Post subject:  
This thread is continued here:
http://www.murga-linux.com/puppy/viewtopic.php?p=329955
_________________
Between depriving a man of one hour from his life and depriving him of his life there exists only a difference of degree. --Muad'Dib

Back to top
View user's profile Send private message 
Display posts from previous:   Sort by:   
Page 13 of 13 [186 Posts]   Goto page: Previous 1, 2, 3, ..., 11, 12, 13
This forum is locked: you cannot post, reply to, or edit topics.   This topic is locked: you cannot edit posts or make replies. View previous topic :: View next topic
 Forum index » Advanced Topics » Hardware » Networking » Wireless
Jump to:  


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group

[ Time: 0.0899s ][ Queries: 13 (0.0556s) ][ GZIP on ]