TazPuppy 5.0 rc2
ram memory
ram memory
after downloaded to downloads
folder in ram memory for
example 100 mb and deleted it,
ram is same-
it has 100 mb!!!?
after downloaded to downloads
folder in ram memory for
example 100 mb and deleted it,
ram is same-
it has 100 mb!!!?
Did you try to run tazpuppy at default mode? TazPuppy performs autoconfiguration for Xorgkschewe wrote:Hi
Is there a way to run a xorgwizard or similar. I can boot to shell. If i run startx the system will crash since my device requires 800x600. I tried vga=788 and nomodeset. The vga command works when loading but as soon as the graphic server starts i get the black screen. Suggestions? thanks
TazPuppy beta 34 released
Changes:
* Build from recent slitaz build
* Improved puppy core dialog
Download: https://drive.google.com/open?id=1yp_Ii ... OoEiXQkX6j
MD5 Checksum: 4799bfa1b441881305f6ceeb5d7513e6
Build kit: https://drive.google.com/open?id=1ohYvb ... tSMvKaz7-l
Changes:
* Build from recent slitaz build
* Improved puppy core dialog
Download: https://drive.google.com/open?id=1yp_Ii ... OoEiXQkX6j
MD5 Checksum: 4799bfa1b441881305f6ceeb5d7513e6
Build kit: https://drive.google.com/open?id=1ohYvb ... tSMvKaz7-l
I will try it again with the updated iso. I am running different pups on a very old machine. Xorg only might not recognize it. I have the best luck with kernel 3.4.103mistfire wrote:Did you try to run tazpuppy at default mode? TazPuppy performs autoconfiguration for Xorgkschewe wrote:Hi
Is there a way to run a xorgwizard or similar. I can boot to shell. If i run startx the system will crash since my device requires 800x600. I tried vga=788 and nomodeset. The vga command works when loading but as soon as the graphic server starts i get the black screen. Suggestions? thanks
I do not enough experience yet to figure out all the commands. If there is a manual xorg wizard those usually work best. Every pup is a bit different. I cannot run newer ones without using vga=788 in grub bootup, tahr arcade and bionic lite. I am able to change the kernel in bionic to new but cannot figure out how to use the old, different challenge lol
Neat though I took your kernel and fdrv and zdrv and put it into bionic and it works with additional drivers. i get sound now finally on bionic. I assume the sfs file loads the additional drivers. Thanks.
Im afraid not, because udisks2-volume-monitor already exists in tazpuppy.zagreb999 wrote:please,
put this pet
in future iso-s
it opens perfectly hdd drives
pup-volume-monitor-0.1.11-1-i686-precise.pet
Yes it is, just typezagreb999 wrote:Is there vlc for tazpuppy?
Code: Select all
tazpkg -gi vlc
tzclock_3.0.6-1_i386.deb
tzclock_3.0.6-1_i386.deb
works perfectly in iso 32,
but in iso 33 and 34
can not work
can you resolve problem?
works perfectly in iso 32,
but in iso 33 and 34
can not work
can you resolve problem?
https://pkgs.org/download/vlczagreb999 wrote:thanks
that vlc does not work
there is not way to make
that vlc works
can you upload one?
TazPuppy is based from Slitaz which was rolling-release. That means that the libs was newer than previous. then look for later version of tzclockzagreb999 wrote:
tzclock_3.0.6-1_i386.deb
works perfectly in iso 32,
but in iso 33 and 34
can not work
can you resolve problem?