Page 1 of 1 [12 Posts]  
Author Message
neerajkolte
PostPosted: Sat 17 May 2014, 05:01    Post subject:

Nice set of guides.
Thanks gcmartin.
neerajkolte
PostPosted: Sat 17 May 2014, 04:51    Post subject:

Nice set of guides.
Thanks gcmartin.
Snail
PostPosted: Sat 21 Jan 2012, 03:19    Post subject: Seamonkey Guide minor comments

Thank you for this guide. I have a few comments that I hope may help to improve this very helpful document:

Ironically I wasn't able to open the Google docs site in Seamonkey and had to use Firefox to view it. That is probably something I've done however.

Both my Wifi routers issue IP addresses beginning with 10. not 198. . I believe that this is very common with WiFi routers, which are by far the most common home router type in my country. It might help avoid noob confusion if this was mentioned.

The last link on the Seamonkey page points to the Slacko announcement, not the 528 one.

Have you considered getting this information added to the Puppy Help 101 page, which is a file built into the 528 sfs? Or at least getting a link to your site added there?
gcmartin
PostPosted: Tue 29 Nov 2011, 16:48    Post subject: Placeholder for FATDOG

coming in the future, a SAMBA guide for FATDOG

Pristine usage
To use SAMBA in FATDOG, a user MUST know that a Control Panel utility MUST be run so that the OOTB SAMBA server can provide sharing to the LAN community. The following figure depicts this need and it is advised to Enable and to Start the SAMBA server..
Running the following command shows what is initially being shared.
Code:
# smbclient -U% -L localhost
WARNING: The security=share option is deprecated
Failed to load upcase.dat, will use lame ASCII-only case sensitivity rules
Failed to load lowcase.dat, will use lame ASCII-only case sensitivity rules
Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.6.12]

   Sharename   Type    Comment
   ---------           ----      -------
   data            Disk      Downloads
   IPC$            IPC       IPC Service (fatdog64-9e6-SMB)
   CUPS-PDF    Printer   CUPS-PDF
Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.6.12]

   Server                   Comment
   ---------                    -------
   FATDOG64-9E6         fatdog64-9e6-SMB

   Workgroup               Master
   ---------                     -------
   WORKGROUP            FATDOG64-9E6
There is no Guide at this time for FATDOG tailoring for any user needs.
gcmartin
PostPosted: Tue 29 Nov 2011, 06:00    Post subject: Placeholder for FATSlacko

There is a very simple easy to use document for sharing using FATSLACKO (SPUP) .

FATSLACKO uses a version of sharing (SAMBA) that makes it capable to connect as well as allow connections to all 2009-2011 devices that attach to Windows and MACs (SMB2 protocol units.).

Hope this helps
gcmartin
PostPosted: Tue 29 Nov 2011, 05:56    Post subject: Placeholder for Squeeze-Exprimo
Subject description: Directions for installation and use of SAMBA on EXPRIMO

There is a very simple easy to use document for sharing using EXPRIMO 5.x (EXPRIMO) .

EXPRIMO uses a version of sharing (SAMBA) that makes it capable to conect as well as allow connections to all 2009-2011 devices that attach to Windows and MACs (SMB2 protocol units.).

Hope this helps
gcmartin
PostPosted: Tue 29 Nov 2011, 05:54    Post subject: Placeholder for RACY/WARY

coming in the future
gcmartin
PostPosted: Tue 29 Nov 2011, 05:53    Post subject: Placeholder for Puppy 5.2.8

There is a very simple easy to use document for sharing using PUPPY 5.2x (PUPPY) .

PUPPY uses a version of sharing (SAMBA) that makes it capable to conect as well as allow connections to all 2009-2011 devices that attach to Windows and MACs (SMB2 protocol units.).

Hope this helps
gcmartin
PostPosted: Tue 29 Nov 2011, 05:52    Post subject: Instructions for SLACKO 5.3.x users

There is a very simple easy to use document for sharing using SLACKO 5.3.x (SPUP) .

SPUP uses a version of sharing (SAMBA) that makes it capable to conect as well as allow connections to all 2009-2011 devices that attach to Windows and MACs (SMB2 protocol units.).

Hope this helps
gcmartin
PostPosted: Tue 29 Nov 2011, 05:50    Post subject: Placeholder for Lighthouse (32bit versions)

coming in the future
gcmartin
PostPosted: Tue 29 Nov 2011, 05:44    Post subject: Instructions for LightHouse64 users (similar for Slacko use)

There is a very simple easy to use document for sharing using LightHouse64 (LH64).

LH64 uses a version of sharing (SAMBA) that makes it capable to conect as well as allow connections to all 2009-2011 devices (SMB2 protocol units.).

Hope this helps
gcmartin
PostPosted: Tue 29 Nov 2011, 05:38    Post subject:  How to share your Puppy stuff with others on your network

This thread addresses how to use Puppy distro to share folders in your LAN community using SAMBA.

This thread is a work in progress to try to address the specifics of sharing from the perspective of each separate distro. this is because each distro can provide its own unique way for the SAMBA subsystem to be made available to its users.

Because Puppy is a varied collection of kernels and package management repositories, I felt it best to try to provide individual documents for several primary Puppy Linux distros.

Guides for the following Distros included in this threadPlease post to this thread for assistance in "sharing" content with your LAN PC users should you have problems

On the forum, there is this other thread on SAMBA here, as well, Its information is formatted a little differently to ease use of SAMBA.
Display posts from previous:   Sort by:   
Page 1 of 1 [12 Posts]  

Powered by phpBB © 2001, 2005 phpBB Group